Brand New Rotec R2800 7 Cylinder Radial Aircraft Engine on 2040-parts.com

Brand New Rotec R2800 7 Cylinder Radial Engine

110hp

Never ran, fresh out of the crate.

Complete Kit

Should still be under factory warranty

****Can Help crate and ship world wide*****

From the Rotec website

• Purpose Built 7 Cylinder Radial Engine
• Matthew & Paul Chernikeeff
• Seven Cylinder Four Stroke Radial Engine
• 80 x 80 mm (3.149” x 3.149”)
• 2800cc (172ci)
• 2 Valves per Head. Push Rod Operated. Over Head Valve
• Fully Machined Aeronautical Grade Aluminium
• Steel 4140. Precision Honed to a Perfect Finish and Exact Tolerance
• Steel 4140 Billet. Nitride hardened
• Steel 4140. Deeply I Beamed. Lubricated by Mains Oil Pressure
• All Nitride Hardened and Precision Ground to Exact Tolerances
• 810mm (31.9”)
• Starter Motor, Alternator, Carburettor, Stub Exhaust
• Single Bing 40mm Constant Depression Carburettor
• Mechanical Fuel Pump (with Optional Electric Back-up Pump in Parallel)
• Compatible with Avgas100LL or High Octane Mogas
• 22 litres/hr (5.81 US gal/hr) (4.84 Imp gal/hr)
• Dry Sump. Geared Oil Pressure. Primary & Secondary Scavenge Pumps
• Dual: Hall-Effect Electronic and Magneto
• 12V Rear Mounted. Built-in Solenoid for Reliable Engagement
• 35amp Small Rear Mounted with Built in Voltage Regulator
• Two per Head. (NGK DCP8E)
• 102Kg( 224lbs)
• 110HP @3600rpm Geared
• Via Planetary Speed Reduction Unit (PSRU) 3:2 Engine:Prop rpm
• Precision Ground and Matched Taper
• Standard. Same as used for a Rotax 912 Series
• 2 Blade: 76”diameter 55”pitch or 3 Blade: 67" diameter x 55" pitch
• 2300 - 2400rpm Take Off. 1900 -2100rpm Cruise
• Air cooled - no lugging around water or radiator.
• Short Stubs fitted as Stanard. Collector ring optional extra.

Each Rotec R2800 is supplied with:

• 1 x 40mm Bing Carburetor& Rubber Coupling and 2 x Hose Clamps
• 1 x 3 Planet 3:2 reduction PSRU (gearbox)
• 1 x Starter Motor & Nyloc M 10 Nuts
• 1 x Alternator and Alloy Spacer inc. Bolts Nyloc nuts and Washers.
• 7 x Exhaust Stubs & 14 x Bolts & Washers
• 1 x Prop Washer & 6 x Bolts & Washers
• 1 x Ignition Module & Heat Sink Cream
  
• 1 x 12 Volt Ignition Coil (Auto Style)
  
• 1 x Magneto Trigger (Solid State)
  
• 2 x Rotor Buttons (Ignition)
  
• 1 x Ignition Wiring Harness
  
• 1 x Oil Filter Block & Auto style filter Including Filter
• 1 x In line oil filter between dry sump and scavenge pump
  
• 2 x Steel Top Engine Mount Cups (Weldable)
  
• 2 x Steel Lower Engine Mount Pins (Weldable)
  
• 4 x Sets (8 pcs) Rubber Engine Cushions
  
• 2 x Lower Engine Mount M8 Cap Screws &
• Nyloc Nuts
  
• 2 x Lower Alloy Stepped Mount Washers
  
• 2 x Upper Engine Mount Nyloc M 10 Nuts
  
• 2 x Upper Mount Plain Alloy Washers
  
• 2 x Upper Mount Flared Steel Inner Sleeves
  
• 1 x Operations and Service Manual