Find or Sell any Parts for Your Vehicle in USA

1983-95 Ford Mustang 17 Tooth Speedometer Gear & Clip Kit Manual Transmission on 2040-parts.com

US $29.89
Location:

Simpsonville, South Carolina, United States

Simpsonville, South Carolina, United States
Condition:New Brand:FORD Manufacturer Part Number:17271I-K

$$$$$ FREE SHIPPING $$$$$

Ford

In order to keep your speedometer functioning correctly the proper speedometer gear should be installed!

Product Description

17 Tooth Speedometer Gear & Clip Kit
Changing out the gears in your 1983-1995 Ford Mustang? Don't forget to grab the correct drive gear. When you change the rear end gears in your Mustang you will need to re-calibrate your speedometer by installing a new speedometer gear. Our Mustang speedometer gears are inexpensive and only take a few minutes to replace! Check out our speedometer gear installation instructions on how to change the speedometer gear in your Mustang.

Complete Setup
Unlike other shops, when you purchase a speedo gear the speedo gear clip is included! Don't mess around with broken or missing speedo clips and don't bother purchasing them separately, order from us and get everything you need for a clean speedo gear install all at once!

Note
- This is the speedometer DRIVEN gear. 
Application
- Fits 1983-1995 Ford Mustangs

Benefits

  • Corrects Speedometer Readout
  • 15 Minute Install

Features

  • Includes Speedo Gear Clip

What's in the Box

  • (1) Speedo Gear
  • (1) Speedo Gear Clip

1983-95 Mustang Speedometer Gear Installation Instructions

Overtime your 1983-1995 Mustang will require some repair. One of the most common components that end up failing is the speedometer gear. Follow along with us step by step as we replace this key component with a high quality replacement speedo gear..    

Tools Needed:

  • 11mm socket or wrench
  • Small Flat Tip Screwdriver
Step 1:
Carefully raise and support the vehicle.
Step 2:
The speedometer gear is located, on the driver’s side of the Mustang's transmission tailshaft.
Step 3:
Use an 11mm socket or wrench to remove the securing tab to the VSS sensor and speedo gear.
Step 4:
Pry and remove the retaining clip from the gear.
Step 5:
Install the correct speedometer gear and retaining clip.
Step 6:
Lubricate "O" ring seal and reinstall VSS sensor and gear in reverse order



Marchionne, Fiat execs tighten grip on Chrysler under unified management team

Thu, 28 Jul 2011

Sergio Marchionne, CEO of Fiat S.p.A. and Chrysler Group LLC, will retain oversight of the two automakers in North America under a single management team dominated by Fiat-bred executives. Four regional chiefs will be in charge of Fiat and Chrysler operations in North America, South America, Europe and Asia effective Sept.

Lamborghini Gallardo LP560-4 Bicolore (2011)

Thu, 27 Jan 2011

This is the new Lamborghini Gallardo LP560-4 Bicolore, just unveiled at the 2011 Qatar motor show. The bicolore bit – essentially this is a Lamborghini Gallardo available with a two-tone finish. The roof, pillars, engine hood and rear spoiler are painted black, while the body is available in a choice of five colours: Giallo Midas (yellow), Arancio Borealis (orange), Grigio Telesto (grey), Bianco Monocerus (white) and Blu Caelum (blue).

Chrysler and Fiat get a new logo, Dutch incorporation, UK tax shelter

Wed, 29 Jan 2014

Chrysler Group reported an increase in earnings for the fourth quarter as the launch of the2014 Jeep Cherokee and higher U.S. sales helped the automaker to its third straight annual profit. In a separate announcement today, Chrysler and Fiat said their combined company will be renamed Fiat Chrysler Automobiles NV.