Find or Sell any Parts for Your Vehicle in USA
Boat Parts > Outboard Engines & Components > Complete Outboard Powerheads

2003 - 2005 Mercury Optimax 3.0 Liter 250 Sport Jet Complete Bolt In Unit on 2040-parts.com

US $4,450.00
Location:

West Sunbury, Pennsylvania, United States

West Sunbury, Pennsylvania, United States
2003 - 2005 MERCURY OPTIMAX 3.0 Liter 250 SPORT JET COMPLETE BOLT IN UNIT, US $4,450.00, image 1
“WITH OUR BUYING POWER AND STATE OF THE ART MACHINES WE CAN SAVE YOU MONEY $$$$ WITHOUT SACRIFICING QUALITY !! With OVER 20,000 powerheads done and 200 marine dealers to our credit we can offer you same as new powerhead for a fraction of the price”
Brand:Mercury Jet Stroke:2-Stroke Engine(HP):250 Country of Manufacture:United States Manufacturer Part Number:889437A2 Core charge:Reuseable sport jet same mode as auction unit

 

OUTBOARD REBUILDER SINCE 1972 !!

**COMPLETELY REMANUFACTURED

THE E BAY Price is a core exchange auction

WE WILL SHIP ANYWHERE IN THE U.S. & Canada With 85% DISCOUNT

WITH OUR BUYING POWER AND STATE OF THE ART MACHINES WE CAN SAVE YOU MONEY $$$$ WITHOUT SACRIFICING QUALITY !!  With OVER 20,000 powerheads done and 200 marine dealers to our credit we can offer you same as new powerhead for a fraction of the price.


YOU ARE BIDDING ON A  REMANUFACTURED  COMPLETE BOLT IN 2005 MERCURY M2 250hp SPORT JET.  PART no. 889437A2

THIS SPORT JET IS A FRESH COMPLETE UNIT READY TO INSTALL IN THE BOAT. NEW PISTONS,  Injectors have been rebuilt, fuel system rebuilt, fuel pump rebuilt, fuel rails rebuilt.

                   ALL NEW PARTS, NO SHORT CUTS !!! Pre run and ready to roll.


This powerhead comes  with our 1 year parts replacement warranty.  Message us through eBay for a copy of our warranty

If TROUBLE SHOWS UP WE WILL BE HERE TO HELP!!!



INSTALLATION AVAILABLE IN :   Pittsburgh, PA / Ft. Lauderdale, FL / Portsmouth ,VA / De Land, FL /Cape Cod, MA /Atlanta,Ga/ Annapolis MD / North Carolina, Austin TX , Sacramento, Ca or any certified Mercury dealer


At Outboard Rebuild when we use the word ReMANUFACTURED you can be 100% sure that all cylinders have been machined by only the best machines that are available. Rotler F3 boring center that is designed to do blind hole engines,  Rottler HP7A Diamond computer assisted hone for unsurpassed cylinder wall finish, critical in 2 stroke motors that rely on oil/gas mix that is needed to lubricate, We machine all critical surfaces back to uniform for proper gasket sealing. We install NEW parts, Pistons, Piston rings, wrist pin's, Oil gear, thermostats,rod bearings, crank seals, the list goes on and on.. We feel you should get what you pay for " A powerhead that last YEARS as they should

  The Industry (outboard remanufacturing) standard for rebuilt motors is ONLY 100 hours per outboard repair, and a loss of up to 20% power loss . Here is the problem:  piston and ring seating is dependent directly on cylinder wall finish. To accomplish the proper finish, the method used is referred to as "plateau finish". This process is how today's automobile motors go well over 100,000 instead of maybe 50,000 miles like they used to. To obtain this finish in a blind hole motor (outboards) you can't use automotive machining methods. Special machines using diamond precision computer controlled hones are needed. These machines with their support equipment are a must on modern outboards, gone are the days that you can do this correctly at a dealer or in a garage. With this in mind we attempt to educate.

   For the uneducated customer who looks only for low price also gets a new friend.  Who? The dealer or person who is going to rebuild your engine again, to the industry standard, AGAIN...


DID YOU KNOW WE ARE THE ONLY REBUILDER THAT REBUILDS OUTBOARD CRANKSHAFTS IN HOUSE ?  All our Rebuilds have the crankshafts replaced or refinished. We don't put new bearings on a used crankshaft without at least checking integrity to .002 of an inch then polishing. We are the only rebuilder who can refinish crankshafts if needed with the proper equipment, "submerged arc welding" for hardened nitrated outboard crankshafts.  
 

 

                       We will arrange all shipping by FedEx freight. We ship daily and will pass our 85% discount on to you !! Residential service available with lift gate.

question on shipping 877 983 2537

Complete Outboard Powerheads for Sale

Bentley Mulsanne convertible concept debuts

Sun, 19 Aug 2012

Bentley will expand the Mulsanne lineup with a glitzy convertible version, previewed by a concept that debuted at Pebble Beach. The British droptop would likely share mechanical pieces with the coupe, meaning a twin-turbo 6.75-liter V8 making 505 hp and 752 lb-ft of torque paired with an eight-speed automatic and rear-wheel chassis. Technical specifications were not confirmed.

To Infiniti and beyond - new Q30 concept revealed for 2013 Frankfurt Show

Mon, 09 Sep 2013

This is the Infiniti Q30 concept premium hatchback, set to take on BMW’s 1 Series, the Audi A1 and the Mercedes-Benz A-Class in the upmarket family hatchback sector. Unveiled ahead of its official world debut at the 2013 Frankfurt Motor Show, MSN Cars was at the exclusive preview event in Milan. We spoke to head of Infiniti design, Alfonso Albaisa to dig deeper into the inspiration behind the Q30 concept and the future of Infiniti’s road cars.

Bruce Weiner Micro Car auction: Day 1 wrap

Sat, 16 Feb 2013

Yesterday's strong bidding left many attendees in disbelief. As the gavel fell on a 1959 Goggomobil TL-400 Transporter Pickup for the top pre-auction estimate of $125,000, anyone who had dismissed RM's estimates as optimistic was reappraising the situation. Several people have brought up the legendary $112,000 sale of an Amphicar at Barrett-Jackson's Scottsdale sale in 2006.

2040Parts.com © 2012-2024. All Rights Reserved.

Designated trademarks and brands are the property of their respective owners.

Use of this Web site constitutes acceptance of the 2040Parts User Agreement and Privacy Policy.

0.04 s, 11803 u