Bat-pac Battery Eliminator Yamaha Tzr-250 Tzr 250 Tzr250 on 2040-parts.com
Miami, Florida, US
The
Bat-Pac Battery Eliminator
Eliminate the need for a battery
for many
Motorcycle ATV Scooter Snowmobile
If your application
has an electric starter, you will lose that function
THE Bat-Pac WAS DEVELOPED
BECAUSE OF A FEW PROBLEMS WITH MANY CHARGING SYSTEMS.
Charging system design in most
Motorcycle, ATV, ATC, Scooter, Snowmobile; rely
on a good battery before the charging system can work properly and to
its designed potential.
Overloading the charging systems components by the use of a weak or
dead battery is a common problem. Extremely low charge conditions
from a weak or dead battery can draw enormous amounts of current in
order to bring the battery up to a charged state. Vibration and extreme
conditions can also damage a battery internally by shorting-out
the plates within a battery, this will cause an excessive current
draw.
Excessive voltage outputs from the charging system are also likely if
running without a battery, or using a battery with low or no fluid
(electrolyte).
Repairs from excessive current draw, or excessive voltage output
usually require an expert's trouble shooting skills, and the
replacement of expensive electronic components including but not
limited to the regulator, rectifier,
stator, armature, CDI, and such.
Replace that heavy,
unreliable, environmentally destructive, lead acid battery.
The Bat-Pac weights in at 2.5 ounces. Size is 1x1x2.5" (Aluminum case
epoxy filled)
The Ba-tPac's
voltage output is
better at idle, and more stable and cleaner at all R.P.M.'s
The Headlight is brighter at idle, than with a good battery on most
models.
The Bat-Pac is maintenance free, and has a Lifetime Replacement
Warranty,
The Bat-Pac is built to endure extreme conditions and temperatures
of +105C / +221F.
Please realize, there is no available power until the motor is running.
If your application has an electric starter, you will lose this
function.
TESTED ON THE FOLLOWING
If your unsure if the Bat-Pac
will work for your application please contact me
Yamaha - RD400E,F, and G from the UK. ; RD400F, and G from Canada ; RD350LC 1980-82 ;
RZ350 ; RZ500 ; TZR250 ; XT250 ; XT500 ; XT600 ; TT600 ; TT600r ; SRX600 ; SR500 ; YSR50 ; DT Enduro's ; DT175 ; DT400 ; FZ ; FZR
Suzuki - RG250 ; RG500 ; RGV250 ; GS ; GT185 ; GT250 ; GT500 ; TC90 ; TC120 ; TS250 R,J, & K ;
TS350 ; TM400 ; T125 ; T250 ; T350 ; T500
Honda - MB5 ; Passport C50 C70 C90 ; XR ; (some CB350, CB500) ; CBR600 F1, F2, F3's ;
CL ; CS ; CM - CM125 CM200 CM250 Z50 ;
Kawasaki = KZ ; GPZ ; ZX ; KLR 250
Polaris - 400 Sport ; Scrambler 400 4X4
Vincent - Black Shadow
BSA - ALL Magneto equipped models
Norton - ALL Magneto equipped models
Triumph - ALL Magneto equipped models
Harley Davidson - ALL Magneto equipped models
XR
ADDING MORE ALL THE TIME
Compatibility issues:
In general, if it has a permanent magnet flywheel,
chances are the Bat-Pac will work.
Older bikes that have a point type magneto can also use the Bat-Pac. If
it uses a
brush type generator/alternator to power the ignition then the Bat-Pac
won't work.
The reason for this is because the permanent magnets can induct enough
current
in the stator coils to start the engine, whereas brush type
charging systems require
a current source with several amps of current capacity to magnetize the
windings of the rotor,
and the primary windings of the ignition coils.
The Bat-Pac works on all that have a
magneto CDI/ stator alternator systems.
The Bat-Pac is compatible with 6 and 12 volt systems, positive
or negative ground.
The Bat-Pac can be used along with a battery for improved voltage
output of the charging system .
Testing a Bat-Pac on a non-compatible charging system will not damage
anything
Bat-Pac
E-MAIL
Bat-Pac FAQ & Instructions
Bat-Pac Compatibility Page
There are many other models yet to be tested .
If your unsure if the Bat-Pac will work for your application please
contact me.
When ordering please specify your application so I can provide the
correct connectors for you.
If you decide to buy a BatPac and it does not work,
or you are unhappy for any reason, Money Back.
Electrical Components for Sale
Harley davidson starter field coil, accel # 40113, 1967-80xl, 1966-82 big twin(US $42.00)
6 volt coil, coventry spares # 45275t(US $35.00)
6 volt coil, one cylinder, # 45275g(US $32.00)
2003 2004 2005 yamaha yzf r6 06-09 r6s left headlight bar switch handle oem z281(US $18.99)
Electrosport industries procom cdi for yamaha warrior 350 2002-2004(US $74.95)
Nib new sealed vance hines throttlepack throttle management tbw harley davidson(US $99.99)
Ex Ford, Mazda designer to head styling at Renault
Fri, 10 Apr 2009Former Ford Motor and Mazda designer Laurens van den Acker will succeed Patrick le Quement as head of design at French automaker Renault. Van den Acker, 43, quit as head of design at Mazda earlier this month. He will join Renault on May 15 and assume le Quement's full responsibilities starting on Nov.
Ford's automotive assembly line celebrates 100th anniversary
Wed, 09 Oct 2013A mere century ago, on Oct. 7, 1913, Henry Ford rigged up a rope tow to get Model T chassis across the floor of his Highland Park assembly plant -- essentially winching cars across the factory floor and adding a set schedule of parts at certain intervals. The implementation may have been a bit primitive, but Ford was on the cusp something big: applying the concepts of the moving assembly line to the complicated, costly process of automobile production.
Concept Car of the Week: Opel CD (1969)
Fri, 24 Jan 2014Despite its sophisticated suspension and spacious interior, Opel struggled to sell its big Diplomat luxury sedan. It was 1968 and Opel simply couldn't compete with Mercedes-Benz, the leader in that segment by far. Bob Lutz, then a young executive at GM Europe, thought of using the sedan's chassis to create a large GT Coupe in an attempt to boost both its sales and profile.