Brand New - Gm 4btn Keyless Entry Remote Fob - Fcc Id: Kobut1bt - Gm#: 15732805 on 2040-parts.com

 Brand New - GM 4BTN Keyless Entry Remote Fob - FCC ID: KOBUT1BT - GM#: 15732805

Fits:

2000 Buick LeSabre
1996 - 2005 Buick Park Avenue (2000-2005 NOT self programmable)
1997 - 1998 Buick Riviera
2000 Cadillac Eldorado (NOT self programmable)
2000 - 2001 Cadillac SeVille
1998 - 2001 Chevrolet Blazer
2000 Chevrolet Impala
2000 Chevrolet Malibu
2000 Chevrolet Monte Carlo
1998 - 2001 GMC Jimmy
1996 - 1999 Oldsmobile 88
1999 - 2000 Oldsmobile Alero
1996 - 1999 Oldsmobile Aurora
1998 - 2001 Oldsmobile Bravada
2000 Oldsmobile Cutlass
1996 - 1999 Oldsmobile LSS
1997 - 1998 Oldsmobile Regency
1996 - 2000 Pontiac Bonneville
1999 - 2000 Pontiac Grand Am

Programming instructions for the 2000 Chevy Impala are as follows and should be universal for any of the above listed vehicles: (not guaranteed)

2.       Press and hold the DISP button on the radio for at least five seconds until settings is displayed.

3.       Press the SEEK up or down arrows until FOB PROG appears on the display.

4.       Press the PREV or NEXT button to enter the submenu. The current selection will have an
        asterisk next to it. BEGIN will be displayed.

5.       Press the DISP button to start programming. When the message PUSH FOB flashes, press and
        hold the LOCK and UNLOCK buttons on the first transmitter at the same time for 15 seconds. A
        chime will be heard to verify the transmitter is learned.

6.    Repeat Step 5 for each additional transmitter up to four remotes total. You do not need to press
        the DISP button again, just press down the LOCK and UNLOCK buttons on the next transmitter
        to be learned to a maximum of four transmitters per vehicle.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

EXIT (Exit Feature Customization Mode): This feature allows you to exit the vehicle customization programming.
To Exit:
1. Scroll until EXIT appears on the display.
2. Press the DISP button to exit programming. A chime will he heard to verify the exit.

Just in case here are the instructions for the 2000 Pontiac Grand Am. These may work if the Impala instructions do not. (program your remote . c0m for others):

1.    Close the vehicle doors.

2.   Turn ignition to the ON position then OFF.

3.   Remove key from the ignition.

4.   Press and hold the driver side door lock switch in the UNLOCK position
      until step 8.

5.   Insert the ignition key into the ignition lock cylinder and remove the key.
      (Do not turn the ignition key in the lock cylinder)

6.   Insert the ignition key into the ignition lock cylinder and remove the key.
      (Do not turn the ignition key in the lock cylinder)

7.   Insert the ignition key into the ignition lock cylinder.
      (Do not turn the ignition key in the lock cylinder)
      Leave key in the ignition cylinder.

8.   Release the door lock switch. The vehicle will sound three beeps in order
      to verify the Program Mode has been activated.

9.   Press the LOCK and UNLOCK buttons together on the keyless remote and
      hold unitl the vehicle beeps twice to verify that the keyless remote has been
      successfully programmed. This may take approximately 15 seconds.

10.  Perform the previous step (9) to program up to four keyless remotesm, including
       any old ones.

11.  Remove the ignition key to exit Program Mode.

Free shipping. No returns.