T04E T3/T4 11PC TURBO KIT+TOP MANIFOLD+DOWNPIPE 88-01 B16/B18 CIVIC/CR-X/INTEGRA
ITEM SKU: TBK-SDD-T04E-63+TM-B-S-TM-60-11TBC-T04E-63 TM-B-S-TM-60 WG-60MM-RD BOITCL-HC88+BOPP-HC88-4PC DP-BD-3 BOV-GS-BL FP-G250 BC-RD WRAP-BK-15M OFL
High Compression/ Boosting T04E Turbocharger
The objective of a turbocharger is to improve the engine's volumetric efficiency by solving one of its cardinal limitations. A naturally aspirated automobile engine uses only the downward stroke of a piston to create an area of low pressure in order to draw air into the cylinder through the intake valves. The pressure in the atmosphere is no more than 1 atm (approximately 14.7 psi), so there ultimately will be a limit to the pressure difference across the intake valves and thus the amount of airflow entering the combustion chamber. Since the turbocharger increases the pressure at the point where air is entering the cylinder, a greater mass of air (oxygen) will be forced in as the inlet manifold pressure increases. The additional air flow makes it possible to maintain the combustion chamber pressure and fuel/air load even at high engine revolution speeds, increasing the power and torque output of the engine.
Specifics and Benefits:
Capable of Boosting Horse Power up to 300+ BHP
High Quality Material, Cast Housing with Durable Steel
| Exhaust (Turbo Manifold) Flange: |
Standard T3/ T4 4-Bolt |
| Exhaust (Downpipe) Flange: |
Standard T3 5-Bolt |
| Intake Inlet/ Outlet: |
3.00"/ 2.00" |
Compressor:
| Trim: |
55 |
| A/R: |
.50 |
| Inducer: |
50.50 |
| Exducer: |
76.00 |
Turbine:
| Trim: |
73 |
| A/R: |
.63 |
| Inducer: |
65.50 |
| Exducer: |
55.90 |
High Performance High Flow Tubular Exhaust Long Tube Turbo Manifold
The heart of any Turbo system is the Manifold and the Turbocharger. These form the basis where the rest of the turbo system is built around. Turbo manifolds have only one, but the most critical purpose in turbo systems, and that purpose is to expel exhaust gas into the turbine of a turbocharger as efficiently as possible.
There is no match for power and performance for tubular stainless steel manifolds. Tubular manifolds are made up of runners coming from each cylinder, meeting up at a collector. Tubular manifolds yield a higher efficiency rate, as each runner is generally the same circumference. This allows for a much smoother flow of exhaust gas to the turbo.
Tubular stainless steel manifolds are chosen over cast manifolds for big power applications. Tubular stainless manifolds feature better and more consistent flow of exhaust gases. Most of the tubular Stainless manifolds also feature the placement of the wastegate flange towards the middle of the collector to allow accurate readings and precise control.
Specifics and Benefits:
Extended High Performance Tubular Turbo Racing Design with Long Tubes for Extra High Air Flow
Made of High Quality T-304 Polished Stainless Steel Alloy Material for Strength and Durability
Tubular Top-Mount Design to Ensure Equivalent Exhaust Flow Rate from each Cylinder
Computerized Mandrel-Bended to Maximize Air Flow Smoothness
TIG Welded CNC Machined Flange for Resistance against Cracking and Wearing
Increase Engine Exhaust Output and Efficiency
60mm/ 62mm External V-Band Wastegate Port and Flange Welded
(Might Require Welding)
Standard T3/ T4 Configuration Outlet
Universal 60mm/ 62mm Wastegate with Spring
Wastegates provide a means to control the boost pressure of the turbo charged engine. Wastegates work to bypass exhaust flow from the turbine wheel. Bypassing the exhaust flow reduces the power driving the turbine wheel to match the power required for a given boost level. Similar to the BOV, the Wastegates uses boost pressure and spring force to regulate the flow bypassing the turbine.
Wastegates are bolted to exhaust manifold or header. The advantage of external Wastegates is that the bypassed flow can be reintroduced into the exhaust stream further downstream of the turbine. This tends to improve the turbine’s performance.
Specifics and Benefits:
High Strength Cast Steel Body with Steel Head
Comes with 12-PSI Spring Installed
Lightweight Aluminum Bolt-On Front-Mount Intercooler
When the charged air enters the end tank, it travels through the tubes of an Intercooler, in which the heat is transferred via fins, where cooler ambient air passes over the tubes. This mechanism further removes heat from air before exiting the opposite end tank and routing to the engine.
Bar and Plate Intercooler functions identically to the Tube and Fin Core, with the exception that, charged air travels through its rectangular shaped passages, which have more surface area; thus, improves cooling effect and power of the charged air. The advantage of this type of intercoolers is that, since the bar and plate core affords up to 35% larger surface area for cooling, a physically smaller intercooler can be used and still retains the cooling efficiency of a larger tube and fin design. This is important for a builder who has a vehicle with a compact opening in the front of it or when there are immovable obstructions present.
Specifics and Benefits:
High Performance Bar and Plate Turbo Racing Design
Made of High Quality T-6061 Aluminum Durable Material
Helps Reducing Engine Inlet Temperature
Allow More Horsepower at the Same Boost Level and Even More Power at the Higher Boost Level
Intercooler Size: 27.00” (L) X 6.25" (H) X 3.50" (W)
Core Size: 17.50" (L) X 6.25" (H) X 3.50" (W)
Inlet/ Outlet: 2.25"/ 2.25”
Direct Bolt-On Front-Mount Installation; Easy to Install
Bolt-On Aluminum Intercooler Piping
Specifics and Benefits:
Made of High Quality T-6061 Lightweight Aluminum Piping
2.50" Piping Diameter
Increase 65% Air Flow comparing with other Standard Piping
Lightweight Stainless Steel Down Pipe
Down Pipes eliminate the stock catalytic converter and reduce exhaust backpressure. By maximizing exhaust flow, this downpipe allows the turbo to spool up and build boost quicker. The result brings out the vehicle’s performance potential by giving it a free high flowing exhaust system.
Specifics and Benefits:
Made of High Quality T-304 Stainless Steel with Computerized Mandrel-Bends
i.e. Maximizing Smoothest Exhaust Airflow; Instantly Gains 10-15 HPs
Inlet/ Outlet Sizes: 2.50”/ 2.50”
Piping Diameter: 3.00" with Welded Flex Pipe
Direct Bolt-On Installation, O2 Sensor Bung Insertion; Requires NO Modification
Type-S Adjustable Aluminum Billet Blow Off Valve BOV
Specifics and Benefits:
Billet Aluminum Body
8 Discharge Ports That Draw In Surrounding Air and Release a Unique Discharge Sound
40mm, Hard-Anodized Valve for Increased Airflow
Dual Spring System Promoted Response and Allows for High Boost Pressures
Holds Up to 30 PSI Boost Pressure
Aggressive JDM Racing Discharge Sound
Aluminum 2.5” Flange Pipe
Specifics and Benefits:
Made of High Quality T-6061 Aluminum, Lightweight, Heat-Persistent Design
2.5" Pipe Size
30 PSI Turbo Boost Controller
Specifics and Benefits:
CNC Machined Aluminum Body
1-30 PSI Adjustable
Stainless Steel Braided Oil Feed Line
Specifics and Benefits:
Made of High Quality Stainless Steel Hose
10AN Fittings Anodized Ends
Inner Diameter: 0.25"
Length: 36.00"
1/8 NPT Fittings Natural Polish Finish
High Tolerance Manifold Wrap
Specifics and Benefits:
Made of High Quality Synthetic Fabric Material
Tested to Tolerate Extreme Heat and Wearing Corrosions
100% Brand New
Professional Installation is Highly Recommended (No Instruction Included)
Package Includes:
1 X T04E Turbocharger
1 X Stainless Steel Turbo Manifold
1 X B-/D-Series 3” Inlet/ Outlet Downpipe
1 X External Cast Steel Wastegate WG
1 X Type-S Blow Off Valve Kit
1 X Flange Pipe
1 X Adjustable Boost Controller
1 X Manifold Wrap
1 X Braided Oil Feed Line
1 X Lightweight Aluminum Intercooler
1 X Set of Aluminum Piping
8-Piece Piping Set Includes:
2 X 180 Degree U-Pipe
2 X 90 Degree Pipe
2 X 45 Degree Pipe
2 X Straight Pipe
8 X Silicone Hoses
16 X Bolt-Tight Clamps
Hardware, such as Gasket(s) and Bolt(s), if Shown in the Picture Above
Application:
90-01 Acura Integra
99-00 Honda Civic Si
94-97 Honda Del Sol VTEC
88-91 Honda Prelude
97-01 Honda CR-V
(ALL Models Above with an I4 B-Series DOHC Engine ONLY)
Please Check Compatibilities for Years and Models
Modification might be Required for Some Vehicles
* Professional Installation Highly Recommended! No instructions included! *
| DOMESTIC LOWER 48 US STATES: |
$0.00 |
| AK / HI / PR / PO BOX: |
$199.98 |
| CANADA: |
$199.98 |
| REST OF THE WORLD: |
$498.98 |
| SALES TAX: |
CA ONLY |
Shipping Information:
- VERY IMPORTANT: Double check shipping address. We are not responsible for incorrect or undeliverable addresses.
- Please use Shipping & Payments tab on top of page for shipping details for your location.
- Shipping to PR, HI, AK and PO Box addresses will be charged the same as shipping to Canada. GU, VI, SAIPAN will be charged the same as international shipping rate.
- For Canada shipping please select the lowest price. We do not offer expedited shipping.
- US Territories such as GU, VI, SAIPAN will be charged the same as international shipping rate. Transaction will be held until a full shipping amount received.
- Some of the packages cannot be delivered to a PO Box. Customer is responsible to ensure PO Box address given is deliverable by the shipping company. Package will be held until a valid physical address is provided.
- Customer assumes shipping charges incurred in shipping to undeliverable address.
- International buyers are responsible for all customs duties, taxes, and other applicable fees incurred by the country's customs/border regulations. Please contact customs for more information.
- We ship 98% of all orders the same or next business day after payment received/cleared. Please understand that once orders are shipped, we cannot control the transit times thereafter. Most orders will ship via USPS First Class/Priority Mail or FedEx/UPS or the best suitable carrier for the specific size of the product.
- We are not responsible for any changes to address after item has been shipped.
|
Return policy:
- 14 Days money back, please notify us within 14 days after you've received your purchased item.
- All return requests must be submitted through your eBay account.
- You have to obtain a RMA (Return Merchandise Authorization) number from us, and have the RMA number written on the return package.
- Buyers pay for return shipping fee.
- Items to be returned must be in re-sellable condition.
- All returns are for refund ONLY. No exchange accepted.
- Returns for refund are subject to a 20% restocking fee.
Terms & Conditions:
- For emissions related items, please check with your local jurisdiction for emission specific requirements before purchasing.
- All items do not come with installation instruction unless otherwise specified.
- If item is questionable, please consult your local professional/mechanic before making purchase.
Contact:
- Please use the "Ask A Question" form above to contact us. Please note that we only work from 9am-6pm PST M-F but are OFF on the weekends so messages sent after business hours especially on Friday, will be answered the following Monday.
|
  | |
|
