General Information |
Item Picture |
This is a full interior replacement, all the size
data mirror with factory seat covers. not those cheap,
run-of-the-mill seat covers. Your current cloth comes off then our
interior goes on. Your vehicle will look just like it came from the
factory with new skin! That is good way let your fabric seat or
abrasion leather seat upgrade band new skin.
We guarantee all
our products made by high quality Genuine Leather. High quality
materials are carefully select for all our covers. We use Heavy Duty
Double Stitching and each piece of the cover is sewn on 1/4 foam to
make more comfort and perfect after professional
installation.
Fully custom applications are available. We do
single tone color or any two tone color. Perforation centre also
available upon request, this option will offer more permeability
compare to the regular cover.
|
|
Vehicle Information |
|
|
|
Part Number: |
MMA |
Brand: |
Nissan |
Model: |
MAXIMA |
Year: |
2004-2006 |
Pattern: |
A |
Pattern Description |
|
|
|
|
MMA-A |
|
|
Item GSC-MMA-A can be installed for
2004-2006 Nissan MAXIMA seats.
If you can not make sure the seats pattern does fit your vehicle.
please contact us to confirm your order info. |
|
|
|
|
|
|
Item Specification |
|
|
|
Rear Backrest Cover |
X 2 |
Rear Cushion Cover |
X 1 |
|
Rear Headrest Cover |
X 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Basic Leather Cover Installation Guide |
These are OEM style replacement seat covers that are die cut and
custom tailored to tightly fit your specific vehicle's year, make
and model, not slip covers. Your old seat covers must be removed and
replaced by the set that you have purchased. You cannot install your
new seat covers over your existing seat covers. Remove the seats
from the car. Remove the seat back from the seat bottom--bolts hold
them together at the hinge. Remove all plastic panels, handles and
knobs, and head rests from the seats. Covers are attached with hog
rings. Take care in removing your old seat covers, do not cut or
damage them. Do not discard your old covers until you have
completely installed your new seat cover set. |
|
On covers that are attached with hog rings, cut all existing
factory hog rings and remove cover, slipping it off as you would a
pair of pants or shirt--do not cut your old covers when you remove
them. You must then remove the hold down wire rods from the listings
(sacks) of the back of the old seat covers and slip them into the
new seat cover's listing sacks. Correctly position the cover on the
foam (it is important to take your time--improper installation will
cause wrinkles) and hog ring the hold down rods where the old cover
was attached and stretch the cover over the foam, and attach it to
the frame in the same manner the old cover was attached. It (the
hold down rod) must be attached firmly into the foam channel (in the
seat foam) and to the wire or rod in the seat foam, or your cover
will not look tight and smooth. If you have too many wrinkles in the
seat cover when you are done hog ringing it down to the foam, simply
cut and remove the hog rings and reposition the cover and/or the
listing sack until you have a nice tight, smooth look. Your seat
cover should look smooth with a minimum amount of wrinkles when you
are done. These seat covers, headrests are manufactured to fit
tightly You must install them correctly for a professional look. If
you find that you have too many wrinkles when you are finished,
simply clip and remove the hog rings, and reposition the seat cover
and try again. Make sure that you take note of where your seams are
in relation to the corners of the seat foam. The seams should be
located in the same area on your seat foam that the old cover's
seams were located. You will be able to see the seam marks left on
the seat foam by your old covers. You may have to put the cover on
the foam and work it around until it is positioned properly, then
roll back the edges and start to hog ring or push down hard to
fasten the velcro. Positioning is important for a proper wrinkle
free fit. |
|
Hint: If you are uncertain you can remember how your old cover
was hog rung down, take pictures of how the old cover was attached
before removal, or as you are removing it. For best results, use a
heat gun (or hair dryer), or steamer to make the material more
pliable and it will also help remove any minor wrinkles that you may
have when you are finished. (Usually the heat from the sun after you
have your seats back in your vehicle, and a few days will take care
of most minor wrinkles.) Be careful using the heat gun, hair dryer
or steamer, since too much heat can damage the leatherette or
genuine leather. USE CAUTION! Use the steamer on leatherette only
and not on the genuine leather. Remember, if you have any major
wrinkles in your seat covers, they are not installed properly and
you should remove and reposition them until you have corrected the
problem. |
|
Extreme care should be taken not to rip/tear the new covers at
the seams while installing them. Improper installation and careless
pulling when installing your covers can result in rips or tears at
the seams. Use silicone spray on the seat foam and the inside of the
seat covers (do not spray silicone on the genuine leather or
leatherette) before installation to help your covers slip on, also,
some covers will install easier if you turn your cover inside out,
position it properly, then simply roll it down starting at the top.
Again extreme care should be taken not to tear the new covers at the
seams. These covers are manufactured to fit tightly. When installing
headrests some installers use thin plastic (garbage bags work fine),
silicone spray (inside the covers and on seat foam only, do not
spray on genuine leather or leatherette) or baby powder over the
foam to help the cover slide on easier. This trick also may be used
for installing the seat cover backs and bottoms to help them slide
on easier. Seat covers, armrests/console covers and headrests are
made to fit tightly and may take some patience to install them. If
you take your time when installing your new seat covers, with
attention to detail, and you will have a new interior to be proud of
for years to come. Remember to care for your leather properly. Use
of mild soap and a slightly damp sponge to clean light soil, and the
use of a good genuine leather conditioner/cleaner is recommended.
Your local auto parts store carries a variety of them. We are not
responsible for improper installation of seat cover sets by
nonprofessional /
inexperienced. |
the carbon
fiber auto seats heater system is best heating system in the world.
it has been adopted in high level car many years. carbon fiber auto
seats heater system is compose by many of the independent carbon
fiber heating unit. thin and easy to install, also you can cut out
it to fit your seats pattern. it compared to traditional metal
resistance wire heating system. obviously, carbon fiber heating
system has more advantages. it can instead traditional heating
system completely.
what's different with traditional
heating system?
in traditional heating system. 1-3 piece
resistance wire distributing in each piece of the heating pads. If
there is a break or damage such as overheating on resistance wire.
the entire the heating device will be out of work. in carbon auto
seats heater system. it adopt Parallel Technology for heating
element. each heat pad come with many of the mutually independent
carbon fiber heating element. it will ensures the reliability of
heating system. |
|
|
|
operating voltage: 9.6V ~ 15V Power: 90W (rated
voltage 13.8V) 3-year quality assurance |
The long life Ultra-thin, easy to install and
cut-able maintain constant temperature, Heat spread
evenly |
|
| |