Clevite Rod Bearing GM 348 5.7L 1958-1961 HP .019in. Set Of 8

NORTHERN AUTO PARTS WAREHOUSE

NOT SURE OF FITMENT - CALL 1-866-277-0804 OR USE EBAY'S COMPATIBILITY TO ENSURE CORRECT FIT.

OPEN MONDAY-FRIDAY 8 AM - 6 PM CENTRAL STANDARD TIME AND SATURDAYS 8 AM - 4 PM

Click on the image below to get zoomed view of the item

Description
Brand: Clevite
Part Number: CB743H19
Condition: New

General Motors Clevite H-Series 77, Tri-Metal Connecting Rod Bearings fit the following:
348 CID 5.7L Chevrolet V8 cylinder 1958-1961 (High Performance),
409 CID 6.7L Chevrolet V8 cylinder 1961-1965 (High Performance),
366 CID 6.0L Chevrolet V8 cylinder 1966-1998 (High Performance),
396 CID 6.6L Chevrolet V8 cylinder 1965-1970 (High Performance),
402 CID 6.6L Chevrolet V8 cylinder 1970-1972 (High Performance),
427 CID 7.0L Chevrolet V8 cylinder 1966-1998 (High Performance),
454 CID 7.4L Chevrolet V8 cylinder 1970-2000 (High Performance),
502 CID 8.2L Chevrolet V8 cylinder (High Performance).
NOTE ALL: H-Series Performance, No Dowel Hole In Cap Half, To Be Replaced By CB-743HN.

Clevite H-series bearings without dowel holes.

Clevite Connecting Rod Bearing part number: CB743H19 (0.019in. Oversize)

These bearings are identified by a letter H in the part number suffix. Part numbering is based on the same core number as the standard passenger car parts for the same application. These bearings were developed primarily for use in NASCAR type racing, but are suitable for all types of competition engines.

H series bearings have a medium level of eccentricity, high crush, and rod bearings have a hardened steel back and thin overlay. These bearings also have enlarged chamfers for greater crankshaft fillet clearance and are made without flash plating for better seating. Bearings with .001” extra clearance are available for standard size shafts and carry the suffix HX” (X = extra clearance).

Rod bearings are available with or without dowel holes (HD = with, H = without), main bearings are available with standard 180 degrees upper half grooving and with full 360 degrees grooving (H = 180 degrees, HG 360 degrees). Use H series bearings with crankshafts that have oversize fillets and where engines run in the medium to high RPM range. H series bearings should be used if contact patterns obtained with P series parts are too narrow. Contact patterns should ideally cover 2/3 to 3/4 of the bearing surface. See accompanying contact pattern diagrams. If you aren’t sure which type of performance bearing to start with, the H series bearing will be your best choice.

Please note:
Some “H” series bearings will no longer be available with enlarged chamfers. Instead, the bearings will be narrowed in place of the enlarged chamfer to provide greater crankshaft fillet clearance. The new narrowed bearings will be available with a “HN” suffix and will be replacing the standard “H” suffix part number.

It takes Three Layers to be Number One, and Clevite 77 TriMetal are it !

Seizure Resistance:
TriMetal bearings have significantly greater seizure resistance than bi-metal bearings, by as much as 40%.
Load Capacity:
TriMetal bearings can withstand much higher loads for longer periods of time as compared to bi-metal bearings, over 60% higher.
Embedability & Conformability:
The overlay on a TriMetal bearing offers a far more forgiving surface than bi-metal bearings. These features may not be as critical during OE assembly as they once were, but they do offer additional protection that can be extremely beneficial in an engine that is poorly maintained.
Durability:
Clevite 77’s TriMetal bearings not only exceed light vehicle OE durability requirements of 150,000 miles, they also exceed heavy vehicle OE durability requirements of 300,000 miles.
Tolerances:
Because the surface layer of a TriMetal bearing adds an additional manufacturing step, Clevite regularly hold wall sizes to within .0005” as compared to a bimetal that can be held to within .0003”. This stack up of tolerances has nothing to do with quality, suitability, or service life.
Wear Resistance:
While the silicon in the bi-metal material does contribute to slightly improved wear resistance as compared to the Babbitt surface layer of a TriMetal material, it’s at the direct expense of embedability and conformability.

Note: Not even all tri-metal engine bearings are the same. If you want the strongest engine bearings of the highest quality, ask exclusively for the original Clevite 77 Tri-Metal Engine Bearings.

When installing any bearing
DO NOT ATTEMPT TO POLISH THE BEARING RUNNING SURFACE WITH ANY TYPE OF ABRASIVE PAD OR PAPER.
Bearing overlay layers are extremely soft and thin, typically .0005” on high performance parts.
These thin layers can easily be damaged or removed by abrasive media. Because the overlay layer is electroplated,
it may exhibit microscopic plating nodules that make it feel slightly rough.
The nodules are the same material as the rest of the plated layer and will quickly be flattened by the shaft.

This Part Fits The Following Vehicles



	Welcome to our eBay store! To make your purchase as simple and easy as possible, please refer to the store policies listed below. After winning an item in auction or completing a Buy It Now purchase, you have two check-out options:
		Check-Out Now! Click the Pay Now button at the top of this listing to immediately proceed with our checkout and payment process. Please note that the Pay Now button is ONLY available after winning an auction or completing a Buy It Now purchase. Check-Out Later If you do not choose to Check-Out now, you will be notified by eBay via e-mail that you are the winning bidder. There is no need to contact us to arrange payment. We will automatically send you an e-mail within three hours of an auction closing. Our message will contain a link to our simple and secure checkout system, where you will be able to quickly and conveniently pay for your purchase. You may also continue purchasing additional items from our auctions or eBay store. You have 7 days from the end of the first purchase to add additional items to your order. Make sure all of your auctions have ended prior to checking out. All of your purchases will be consolidated into one checkout!
		Payment We accept the following forms of payment.
		Sales Tax For shipments to Iowa addresses, we are required by State law to collect 7 % Sales Tax.
		Shipping Northern Auto Parts ships all domestic orders via UPS. The shipping charge is determined by your shipping method, package weight, and dimensions. If you purchase multiple items from us, we can combine your shipping cost to save you money. Also, just use the shipping and payments tab to calculate your shipping if purchasing more than one of the same item. We are happy to ship items internationally. All duties, taxes, and import fees are the responsibility of the buyer. Please note that items shipped internationally take more days to arrive then domestic orders. International Customers: All duties, taxes, and import fees are the responsibility of the buyer. Attention Australian Customers: We will automatically upgrade any packages over 15 pounds to UPS Expedited to Australia. This will give you better tracking and get you your package faster. Again, we will not charge you any extra for UPS Expediated to Australia on packages 15 pounds or greater. We get great rates from UPS to Australia, and we are happy to pass them on to our customers. Returns You can return your item within 30 days for a full refund minus the shipping cost. If there is any problem with your order, please contact us right away and we will help resolve the situation.
		Customer Service If you have any questions about this product, or any other product featured on our ebay site, you can "Ask Seller a Question". You can also call us at 1-866-277-0804.