For HONDA 35 outboard 
Vinyl decal set reproduction

Digital printing and lamination, is a reproduction.
Made on clear vinyl.

Stickers are produced on self-adhesive vinyl film with lamination.
We use only high-quality films from well-known manufacturers.

Stickers may differ slightly from the original in color, size, shape.
Waterproof, frost-resistant and heat-resistant, petrol-resistant - (if not left for a long time in a petrol environment).
Stickers adhere well to paint, varnish and other cleaned smooth surfaces.
Decals are resistant to ultraviolet light, but over the years, under the influence of sunlight, over time, everything fades and loses color, be it a sticker or paint, etc. But this will not happen in the early years.


1. - Great price.

2. - Vinyl films from only the best manufacturers.

3. - There is expedited delivery.

4. - Possibility to supplement the complete set with stickers, plates on your engine, according to your photos and measurements. - Free of charge. (Send photos and measurements in a message to us).

5. - You accidentally spoiled a part of the sticker, don't worry, we can send small parts to you free of charge, you pay only 8-10 $ shipping for standard delivery or in an envelope. Send us a photo of the damaged part.

6. - Didn't find the stickers you were looking for? Send us a message with a photo. If we do not have such decals, then we will ask you to measure parts of the stickers, according to old samples. We will make the kit for free, pay only for the delivery 8-10 $.

7. - Ability to change color, font, size of decals.


This sticker set does not have large parts. With experience, you can easily apply stickers to a dry area. If you are inexperienced and unsure about gluing stickers without wrinkles and without air bubbles. Use some soapy water.

Instructions for correct gluing.
1. The ambient temperature is not lower than +10 C and higher.
2. Prepare about 300 grams of water in the sprayer,
      (preferably distilled water), and add to it
      (pure soap without additives) a couple of drops or very finely
      piece of solid. Mix well.
3. Prepare a felt spatula to remove from under
      stickers with water and air drops.
4. Prepare clean, non-marking wipes.
      particles.
5. Prepare ethyl alcohol to remove fat from
       surface.
6. Accurately measure the place for gluing.
7. Thoroughly clean the surface of the bonding area.
       (Napkin with ethyl alcohol.)
8. Remove large portions of stickers from backing paper. (Large drawing on the side.)
9. Spray large parts with water spray.
         stickers on the adhesive layer and on the surface on which
         stickers will be applied.
10. Paste the sticker on the surface you need,
         secure the sticker by pushing it into place and extruding
         Accumulated drops of water with a spatula, removing drops
         water to the edge of the sticker.
11. After pasting, you need to wait about 24 hours.
   Attention.
         You don't need to test for strength.
         Good bonding takes 2-3 days.
        

Worldwide shipping.

__________________________________________________________________________________________________________________________

TRADEMARK LAW:

Protected names belong to their owners. All of the names of brands, goods or information providers mentioned in this offer belong to their owners and are reproduced without guarantee of free availability. The names are either registered trademarks or should be treated as such. Please note that the rights to all logos, brand names, trademarks, etc. lie with their respective owners.


We are not liable for damage resulting from the improper use of third-party brands, even if we produced this film. The buyer declares that he is in possession of the copyright and/or trademark rights required for the services he has commissioned or, if he is not the author and/or trademark owner himself, has obtained permission from the author and/or trademark owner to use the image, trademarks and/or names. The seller does not check whether the customer is in possession of the copyright and trademark rights required for the services to be provided. Liability towards the third party with regard to copyright and/or trademark claims is therefore excluded for the services commissioned.

The production takes place exclusively in and after customer order.