UPGRADE YOUR RODS FOR ULTIMATE HIGH HORSEPOWER RELIABILITY
Adding larger turbo or more boost to your engine? Upgrade the weak links in your block and keep your engine together reliably with HP's forged Titanium connecting rods!
Product Features
• Forged and CNC machined from vacuum drawn 2 pieces of Titanium Alloy
• Super light and the weight is 40% less than 4340 alloy Rods. Combination tested to 800HP on 4 cylinder engine
• Honed to exacting tolerances within 250 millionths of an inch
• Each connecting rod set is balanced to weights within +/- 1 gram
TECHNICAL DIMENSIONS
Center to Center: 163.5mm
Wrist Pin Diameter: 23mm
Pin End Width: 25.8mm
Big End Journal Width: 32.7mm
Big End Journal Diameter: 60mm
Rod Bolt Dimensions: 7/16"
All HP rods are designed specifically for the application using relevant cylinder pressure and other application-specific factors. We put our vast European engine knowledge to use when designing each application.
Honing the connecting rod big end in-house on state of the art equipment ensures the tolerances are set correctly to ensure proper bearing operation. Lesser quality rods are often not honed with the same attention to detail.
Made from strong and super-light 2 piece Titanium alloy these rods will withstand almost everything you can throw at them and reduce huge weight of your rotate system for faster response in high rpm engines.
HP BOLTS
All HP rods could come with high quality rod bolts similar with ARP 2000, tensile strength higher than 200,000 psi.
TECHNICAL DETAILS
Connecting rods are some of the highest stressed components in an engine and thus require extreme attention to detail to ensure proper operation and reliability. Hentch Performance ensures the success of your next engine build by putting each set of connecting rods through a rigorous quality control process. For years Hentch Performance Rods have been an integral part of delivering the power that the highest powered turbo setups and race engines demand.
Extra attention has been paid to even the smallest details such as the bearing tangs, wrist pin fit, and big end side clearance, providing a level of fit and finish not found anywhere else. Each and every set is finish machined and honed in-house for perfectly round and on size big-end bores, resulting in the industry's lowest failure rates. All rods in this series feature generous wrist pin oiling and optional rifle drilling. One of the hallmarks of a high quality connecting rod is its strength to weight ratio. In order to create this balance of strength and lightweight, our optimized H beam design is utilized and validated using modern CAD drafting and FEA analysis techniques. These techniques ensure the rod is as light and strong as possible, perfected for today's powerful and high rpm European applications.
FAQ
ARE THESE ARE A DIRECT REPLACEMENT FOR MY FACTORY RODS?
Make sure all of the dimensions are same as your original rods or seeking support from your tuning technician.
ARE THESE CONNECTING RODS FORGED?
Yes, these Hench Performance Connecting Rods are made from tough and durable and LIGHT Titanium forgings. These forgings far exceed the quality of most factory rods that are typically made from powdered metal as a cost-saving measure.
WHAT OTHER PARTS WILL BE NEEDED TO INSTALL MY NEW HP CONNECTING ROD SET?
At a minimum, you should use a new set of connecting rod bearings when installing rods.
DO THESE RODS REQUIRE ANY ADDITIONAL MACHINE WORK FOR INSTALLATION?
HP connecting rods are delivered to you in "ready to install" condition. Other engine machine work may be required though when rebuilding an engine, such as decking the block or boring and honing cylinder walls.
IS BALANCING THE ENGINE REQUIRED WHEN INSTALLING THESE CONNECTING RODS?
Since HP rods are sold in balanced sets this is not required. For extreme performance application, this can still be done if desired.
WHAT IS THE MAXIMUM RPM LIMIT OF THESE RODS?
The maximum RPM limit can be affected by many factors. In this application, we suggest not exceeding 8000 RPM with HP bolts. If you plan on exceeding this RPM level, consider upgrading to ARP 625+ bolts.
WHEN SHOULD I UPGRADE TO ARP 625+ ROD BOLTS?
Generally speaking, high RPM conditions put the most stress on rod bolts as the rod and cap are literally being pulled in opposite directions. If you plan on pushing your engine far past factory redline or 8000 RPM we would suggest upgrading to 625+ ARP bolts.
WHAT IS THE HORSEPOWER RATING ON THESE CONNECTING RODS?
Many high horsepower vehicles all over the world using HP rods. We rate our 4 cylinder H-beam rods for 800+ HP.
WHAT ARE THE MOST COMMON REASONS FOR CONNECTING ROD FAILURE?
As one of the highest stressed components in the engine, there are several things that can contribute to a failure. The most common failure is caused by improper installation followed by improper tuning. We recommend that you seek professional help for both installation and tuning. Oiling system health is also essential to ensuring safe engine operation. Momentary oil starvation can result in spun rod bearings and engine failure. In extreme applications also be sure that you are using heavy duty wrist pins.
SHIPPING
We have stable contracted shipping agent which have obviously advantage on cost and delivery time.
For customers from European countries, strongly recommend you to choose DHL which including all tax and VAT in destination.
For the other customers, we could send by UPS or DHL and normally it needs 5-7 business days.
RETURNS
If you need to return your parts we will accept returns within one month as a new/unused item in its original box for a refund/exchange. If you have a problem or need a different part just contact us any time and we will help you to get what you need.
QUESTIONS ON FITMENT FOR YOUR APPLICATION?
If you are not sure if the parts will fit, please send us a message and we will let you know within one business day. If we can keep a mistake from happening before the purchase that is always a plus for You and us.
PHOTO DISCLAIMER
The pictures shown are stock pictures and may be slightly different than the actual part, please refer to the description of this listing for proper fitment and specs. Please send us a message with any questions you may have.
THANK YOU!
We want to thank you for looking at our products and look forward to supplying you with quality parts for many builds to come!