8-inch diameter and 33mm taper with idler bearing
1-pound lighter than 2021 production TEAM clutch
5% reduction in inertia
Compact design with 25mm or 14.1% reduction in width
When installing a new clutch, it is recommended to replace the drive belt or premature belt failure could occur
Note: As an alternative to the 2623-325 Drive Clutch Spacer, you can also use the shorter 2623-308 Drive Clutch Bolt with the original 1623-649 washer
Requires the 0744-080 blue puller to remove this clutch (Sold separately)
Requires six 2623-317 ring gear/damper ring screws with new patchlock threadlocker (Sold separately)
Requires the 8639-454 cam arm pin kit (Sold separately)
Does NOT include cam arm weights, pins, screws, washers, or ring gear screws and will need them added for specific model and altitude calibration
Includes clutch with (1646-009) 85/225-pound spring installed

Replaces Part # 0746-933

Direct replacement for the following models:

2022-2024 M 8000
2022-2024 Norseman 8000
2022-2024 Riot 6000, 8000
2022-2024 ZR 6000, 8000
(Excludes 2024 600)

Can be used to replace the 0746-862, 0746-869, & 0746-881 TEAM clutch that came stock on the following models.
You will need to remove drive clutch washer, remove adjuster in driven, install 2623-325 drive clutch spacer, and install 0627-107 belt. (Sold separately)

2016-2017 M 6000
2016-2017 XF 6000
2016-2017 ZR 6000

Can be used to replace the 0746-862, 0746-869, & 0746-881 TEAM clutch that came stock on the following models.
You will need to remove drive clutch washer, remove adjuster in driven, install 2623-325 drive clutch spacer, and install 0627-111 belt. (Sold separately)

2016-2017 M 8000
2016-2017 XF 8000
2016-2017 ZR 8000

Can be used to replace the 0746-885 & 0746-888 TEAM clutch that came stock on the following models.
You will need to remove drive clutch washer and install 2623-325 drive clutch spacer. (Sold separately)

2018-2019 M 6000 & 8000
2018-2019 Norseman 6000 & 8000
2018-2019 Pantera 6000
2018-2019 XF 6000 & 8000
2018-2019 ZR 6000 & 8000
2018-2021 ZR 6000 R XC

Can be used to replace the 0746-895 TEAM clutch that came stock on the following models.
You will need to remove drive clutch washer and install 2623-325 drive clutch spacer. (Sold separately)

2020-2021 M 6000 & 8000
2022 M 8000 Early Build
2020-2021 Norseman 8000
2020-2021 Riot 6000 & 8000
2022 Riot 8000 Early Build
2020-2021 ZR 6000 & 8000
2022 ZR 6000 & 8000 Early Build

Clutching calibration chart can be viewed in the 'More Info' tab.
Current list of ADAPT drive clutch calibration components:

1646-001 35/135 LB
1646-002 35/215 LB
1646-003 60/220 LB
1646-004 60/240 LB
1646-005 85/255 LB
1646-006 85/275 LB
1646-007 120/265 LB
1646-008 120/285 LB
1646-009 85/225 LB
1646-010 85/235 LB
1646-011 105/255 LB
1646-012 105/285 LB
1646-013 85/205 LB
1646-014 105/205 LB
1646-015 105/225 LB
1646-016 120/235 LB
1646-017 160/300 LB
1646-018 165/310 LB
1646-019 70/170 LB
1646-020 80/180 LB
1646-021 90/190 LB
1646-109 S2-52
1646-110 S2-54
1646-111 S2-56
1646-112 S2-58
1646-113 S2-60
1646-114 S2-62
1646-115 S2-64
1646-116 S2-66
1646-117 S2-68
1646-118 S2-70