Pair Rear Window Lift Support Shock Strut For Mercedes-Benz SLK230 1998-2004 99
PM1006 Rear Trunk Lift Supports Struts Fit 98-04 Mercedes-Benz SLK230
Fitment:
1998-2004 Mercedes-Benz SLK230 Base Convertible 2-Door Trunk
1998-2004 Mercedes-Benz SLK230 Kompressor Convertible 2-Door Trunk
2002-2004 Mercedes-Benz SLK32 AMG Base Convertible 2-Door Trunk
1998-2004 Mercedes-Benz SLK320 Base Convertible 2-Door Trunk
1998-2004 Mercedes-Benz SLK320 Kompressor Convertible 2-Door Trunk
(Please make sure that it will fit your vehicle before purchase.)
Features:
Patented Multi-lobe Seal makes gas springs more tolerant to vibration and temperature extremes.
Twin Tube internal construction-Premium gas-charged cylinders.
Direct fit,Ensures easy installation and precise operation.
Individually tested for performance and reliability.
Specifications:
Condition:100% Brand New
Interchange Part Number:PM1006
Vehicle Location : Rear Trunk
Extended Length [in] : 13.75"
Compressed Length B [in] : 8.52"
How to install:
1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.
2. Before removing the old lift support, inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.
3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8", then pull the support away from the vehicle and it will release.
4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.
5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.
6. If the ends are not lining up,the support may need to be turned. To do this,attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise until the ends line up.
Notes:
We recommend that the lift supports should be assembled in pairs to avoid an uneven load bearing distribution and twisting.
Please allow 0.5-1inch deviation due to manual measurement.
Package Included:2pcs Lift Supports
Fitment:
1998-2004 Mercedes-Benz SLK230 Base Convertible 2-Door Trunk
1998-2004 Mercedes-Benz SLK230 Kompressor Convertible 2-Door Trunk
2002-2004 Mercedes-Benz SLK32 AMG Base Convertible 2-Door Trunk
1998-2004 Mercedes-Benz SLK320 Base Convertible 2-Door Trunk
1998-2004 Mercedes-Benz SLK320 Kompressor Convertible 2-Door Trunk
(Please make sure that it will fit your vehicle before purchase.)
Features:
Patented Multi-lobe Seal makes gas springs more tolerant to vibration and temperature extremes.
Twin Tube internal construction-Premium gas-charged cylinders.
Direct fit,Ensures easy installation and precise operation.
Individually tested for performance and reliability.
Specifications:
Condition:100% Brand New
Interchange Part Number:PM1006
Vehicle Location : Rear Trunk
Extended Length [in] : 13.75"
Compressed Length B [in] : 8.52"
How to install:
1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.
2. Before removing the old lift support, inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.
3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8", then pull the support away from the vehicle and it will release.
4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.
5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.
6. If the ends are not lining up,the support may need to be turned. To do this,attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise until the ends line up.
Notes:
We recommend that the lift supports should be assembled in pairs to avoid an uneven load bearing distribution and twisting.
Please allow 0.5-1inch deviation due to manual measurement.
Package Included:2pcs Lift Supports
