This is a custom kit for
your Chev or GMC truck!

This is a TrueBend metal brake line replacement kit. All lines are supplied double-flared at each end with S.A.E. specified male inverted flare fittings attached and are ready for quick and easy installation. All brake lines have an extra long nut on one end to seat in late model deep-seated wheel cylinders. These malleable lines are easy to bend or coil without collapsing the tubing or restricting the flow of brake fluid. Six couplers  and two special master cylinder nuts are included to join lines and attach parts. Instructions are also included.

may not fit ABS units

this kit is for the following: 

1/2 ton trucks

Blazer (Full size) 1969 to 1993
El Camino 1967 to 1988
Chev S10,Mid-Sized Blazer, Durango, Sprot, Tahoe 1973-97
Chev 1/2 ton C10, C1500, R10, V10 1967 to 1997
Chev Van G10 1/2 ton 1967 to 1997
Chev K10 K1500 Suburban 1967 to 1997
GMC Caballero, Laredo, Diablo, Sprint 1967 to 1997
Jimmy, Yukon 2  & 4 wheel drive 1967 to 1997
GMC S15, T15 Sonoma, Gypsy, Jimmy,Typhoon,Syclone 2 & 4 WD 67-97 
GMC Safari Van 1985-93
GMC  1/2 C1500, R1500, V1500  1967 to 1997
GMC Van G1500 1/2 ton 1967 to 1997
GMC K10 K1500 Suburban 1967 to 1997

3/4 ton trucks

Chev 3/4 ton C20, C2500, R20 V20, 1973 to 1997
Chev Van G20 1974 to 1997
Chev K20 K2500  P20 Suburban 1974 to 1997
GMC 3/4 ton C2500, R2500,1974 to 1997
GMC Van G2500 1974 to 1997
GMC  K2500 ,V25001974 to 1997

1 ton trucks

Chev 1 ton C30, C3500, R30  1974 to 1997
Chev Van G30 1971 to 1997
Chev K30 K3500 1977 to 1997
GMC 1 ton  C3500, R3500  1974 to 1997
GMC Van G3500 1971 to 1997
GMC  K3500 4 wheel drive 1973 to 1997

Here is a list of what TrueBend lines are included to do the models above
(you will have extra lines for other projects!)

one 6 inch (3/16")

one 8 inch (3/16")

one 10 inch (3/16")

one 12 inch (3/16")

one 17 inch (3/16")

one 20 inch (3/16")

one 27 inch (3/16")

one 30 inch (3/16")

one 37 inch (3/16")

one 40 inch (3/16")

one 51 inch (3/16")

one 60 inch (3/16")

two 60 inch (1/4")

one 51 inch (1/4")

one 40 inch (1/4")

one 30 inch (1/4")

one 20 inch (1/4")

one 12 inch (1/4")

six unions to joint lines together

instuctions for installation

2 special master cylinder nuts

A total of 27 pieces

This kit contains all the lines to do a wide variety of Chev models, and many different configurations, so you will have unused lines in any installation. These extra lines are a bonus that can be used for other projects

The tubing is double walled, seamless and copper fused with a special inner and outer coating to provide protection from abrasion and corrosion. This is the same tubing that is used on new cars!

All information on lines are for OEM brake systems only. However, this kit has many lengths and will also service most modified systems also.

The lines attached to the master cylinder and brake block may be a non-standard size other than the special nuts supplied.  You may have to get an adapter at a local parts store.

If you need a very sharp bend next to the flare at the end of the line, you will need a bender listed under "tools/supplies" on our Ebay store.

All unions are solid brass to stop rust.

All lines are made in USA or Canada and are 3/16" or 1/4" outer diameter with a factory flare.

Fits following years: 1973 73 1974 74 1975 75 1976 76 1977 77 11978 78 1979 79 1980 80 1981 81 1982 82 1983 82 1984 84 1985 85 1986 86 1987 87 1988 88 1989 89 90 1990 91 1991 92 1992 93 1993 94 1994 95 1995 96 1996 97 1997 98 1998