173-3536 Fit for Johnson/Evinrude Outboard Stator - 4 Cyl. 9 Amp (1988-1998) Cross Flow Engines, Replacement Part 763767 583536 583340 Stator
Fitment:
Interchangeable OEM part number: 173-3536, 583340, 583536, 763767. Outboard Stator For Johnson Evinrude 2 Stroke 4 Cylinder 4 Cyl 9 Amp works on 1988-1998 Cross Flow engines: 65 JET, 80 JET, 85HP, 88HP, 90HP, 100HP, 112HP and 115 HP
Features:
Fitment
This replace stator fits for Johnson/Evinrude Outboard motors 1988-1998 65/80 JET 85,88,90,100,112,115 HP Cross Flow engines.
OEM
Replaces part numbers: 173-3536,763767, 583536, 583340
Nice Material
Made of pure copper material, you have no worry about the wire's short service life.
Must-have part
A must-have part for repair your yacht battery charging system,which is a component on an engine that is attached under the flywheel of the engine that produce alternating current electricity.
Installation Tips:
1. Remove the negative battery cable.
2. Remove the flywheel.
3. Disconnect the original stator wires.
4. Remove the original stator, saving the original bolts.
5. Install the new stator using the original bolts with a good thread-locker applied (CDI 989-3977 is recommended) to
the bolts and tightened to the factory torque specifications.
6. Connect the new stator to the power pack.
7. Connect the new stator to the regulator/rectifier (ignore any stripes on the rectifier as the new stator does not require
the Yellow wires to be connected to a particular rectifier wire).
8. Replace the flywheel according to the service manual.
9. Clean all battery cable connections, both on the battery and the engine.
10. Replace the battery cable.
Troubleshooting the Stator
NOTICE: Any sign of leakage out of the high voltage coils or bubbling around the battery charge windings indicate a bad stator. Check for burned marks on each pole. If a problem is found on the battery windings, we recommend the rectifier/regulator be closely checked or replaced.
No spark on any cylinder:
1. Disconnect the stop (kill) wire and retest. If the ignition now has spark, check the stop circuit.
2. Check resistance between the Brown/Yellow and the Brown wires. You should read approximately 450-600 ohms. DVA (peak voltage) should be 150v or more while connected to the power pack for each .
3. Inspect the flywheel outer and trigger magnets to see if they are loose or broken.
4. Disconnect the rectifier and retest. If the fire returns, replace the rectifier.
No spark on One Bank:
1. Swap the power packs from side to side and see if the problem moves. If it does, the power pack not sparking is likely bad.
2. Check the trigger leads and compare the readings for both sides. The readings should be very close.
3. Disconnect the stop wires and separate them. If the pack that had no spark now has spark, replace the pack that initially had spark.
4. Check resistance between the Brown/Yellow and the Brown wires. You should read approximately 450-600 ohms. DVA (peak
voltage) should be 150v or more while connected to the power pack for each.
High speed miss or weak hole shot:
1. Connect DVA meter between the Brown/Yellow and the Brown wires and do a running test on each set. AT NO TIME SHOULD THE VOLTAGE EXCEED 400v. If it does, the regulator circuit in the power pack is bad. The voltage should show a smooth climb and stabilize, gradually falling off at high RPM (above 5000). If you see a sudden drop in voltage right before the miss becomes apparent, the problem is likely in the stator.
2. Disconnect the rectifier and retest. If the problem disappears, replace the rectifier and retest.
Overcharging
1. Using a voltmeter, check the voltage on the battery and compare it to the voltage on the red wire connected to the starter solenoid to engine ground.
2. If the voltage is high on the engine compared to the voltage on the battery, do a voltage drop test and try to isolate the area where the problem is.
3. If the voltage is the same on the battery and the engine, but is over 15.5 volts at 4500 RPM, replace the battery with a known good high quality MARINE battery.
4. A continued high voltage reading may indicate the need for a regulator/rectifier combination instead of a rectifier only.
Package included:
- 173-3536 Stator for Johnson Evinrude
Feedback is very important to us.
or Negative
feedback. i will do my best to solve the problem, thanks!