Features:

Built to strict quality control standards 100% factory tested.

Consistent starting power with a high quality solenoid that properly engages the starter drive with the flywheel in your vehicle every time the ignition key is turned.

High standards for components like wiring, brushes, insulation, bearings and coatings for consistent performance in all environmental conditions.

High performance machining of the starter casing for ease of installation and solid joining of the starter housing and your vehicle's mounting surfaces

Specifications:

Material:Aluminum

Color:Silver

Placement on Vehicle:Front

Voltage:12

Rotation:CW

Teeth:10

Power Rating:1.4 KW

Starter Type:PMGR

Part Numbers:

ARROWHEAD: SFD0039

CARGO: 112597

FORD: 4R3T-11000-AA, 4R3T-11000-AB, 4R3Z-11002-AA, 5L2T-11000-AA, 5L2Z-11002-AA, 6L2T-11000-AA, 6L2T-11000-CA, 6L2Z-11002-AA, 6L2Z-11002-C, 7R3T-11000-AA, 7R3Z-11002-A, F89U-11000-BA, F89U-11000-BB, F89Z-11002-BA, 4R3T-AA, 4R3T-AB, 5L2T-AA, 6L2T-CA, F89U-BA, F89U-BB

J & N: 410-14045

LESTER: 3273

MAZDA: 1F82-18-400, ZZP2-18-400, ZZP2-18-400A

MOTORCRAFT: SA-860, SA-930, SA-942, SA-945, SA-962, SA-972

REGITAR-USA: S150-333AN

REMY REMAN: SR111006

WAI: 2-1886-FD

Fitment:
Ford Aerostar 1997 V6 4.0L 1st Prod; or 2st Prod

Ford Explorer 1997 V6 4.0L 1st Prod; or 2nd Prod; Automatic Transmission

Ford Explorer 1998-2002 V6 4.0L Automatic Transmission

Ford Explorer 2003-2004 V6 4.0L

Ford Explorer 2005 V6 4.0L To 10/04; From 10/04

Ford Explorer 2006 V6 4.0L To 12/05/05 or From 12/05/05

Ford Explorer 2007-2010 V6 4.0L

Ford Explorer Sport Trac 2001 V6 4.0L

Ford Explorer Sport Trac 2002-2003 V6 4.0L Automatic Transmission

Ford Explorer Sport Trac 2004-2005 V6 4.0L

Ford Explorer Sport Trac 2007-2010 V6 4.0L

Ford Mustang 2005-2010 V6 4.0L Automatic Transmission

Ford Ranger 1997-2011 V6 4.0L Automatic Transmission

Mazda B4000 1998-2007 V6 4.0L Automatic Transmission

Mercury Mountaineer 1998-2005 V6 4.0L

Mercury Mountaineer 2006 V6 4.0L From 12/05/05; or To 12/05/05

Mercury Mountaineer 2007-2010 V6 4.0L

Package include:
1 x Starter

Attention:

How to Install a Car Starter?

1. Disconnect the battery.

2. Jack up the vehicle if need be.

3. Locate the starter.

4. Disconnect the wiring to the solenoid.

5. Remove the starter retaining bolts then the starter.

6. Compare the new starter to the old one.  Slide the starter into place.

7. Insert the starter retainer bolts.

8. Connect the wiring to the starter solenoid.

9. Reconnect the battery.

10. Listen to the vehicle as you attempt to start it.

11. Ensure the battery terminals are clean and secure.Charge your vehicle’s battery.

12. Check to see the starter solenoid is bad.

Note:

Starter Fault Check:

The starter often has failures and phenomena that cannot rotate or rotate slowly. In this case, check the following aspects:

1. The battery has no electricity or the electricity is weak, so the starter cannot rotate or rotate slowly.

2. The starter thread is loose or off, and the switch or adsorption switch fails.

3. The brush is worn out or the brush surface is not correct, and the spring is weak, resulting in poor contact of the rectifier.

4. Excitation coil or armature coil is short-circuited or disconnected.

5. The rectifier is fouled and the mica sheet is protruding, causing poor contact between the brush and the rectifier.