Cylinder Scoring is a serious damage,which caused by improper use and will cost you a lot of money to repair the motor.
Don't do the following will avoid cylinder Scoring:
1，start the motor on bank
2, use the motor when it stop coming out of water
Even if you want test the motor, it should be done in the river!
1.About the noise: all the gasoline machines are noisy, currently we did not test the decibel , but the noise is the same as the motorcycle, so it is a normal phenomenon
2.The machine itself is lightweight, it can use on boat weight of 100kg or less , load-bearing 4 people, but the speed is certainly not the same when one person on it or 4 people on it . Customer who has high expectations on speed, please be noticed
3.It can be marched with inflatable boats, rubber boats or fishing boats
4.Necessary: you have to prepare a boat-motor stand or Hanging board on your boat
Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us).our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!!
About certification:
We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.
Two strokes 3.5 hp and 3.6 hp are controlled by the handle, which is operated by the clutch. There is no Neutral, only idle mode or low speed mode
STRICTLY FOR PROFESSIONAL USE ONLY
Please Note:
There are two pull starter included in the parcel(one is the machine, another one for spare)
We don't supply wearing parts (pull starter)for free.
If you want buy one please click:
Description:
Overall length:92CM
Overall widteh:36.5cm
Overall height:22cm
Transom height:42cm
Full throttle perating range:4000-5000r/min
Speed:10km/h
Type:2-stroke
Ignition system: CDI system
Starting system: Manual start
Staring carburetion system: Choke start
Propeller mark:7-1/45-A(inch)
The engine and the propeller ratio:2:1
Recommended fuel: Regular unleaded gasoline
Fuel to oil ratio: 35:1 （Please be suject to this version, and disregard the manual about this point）
Gear ratio: 27/13
Maximum speed: 10 km / h
Built-in fuel tank: 1.3L
Fuel consumption per hour: 1.5L
When at normal cruising, the appearance of the seventh picture. Falling back the boat, the appearance of the outboard motor likes the eighth picture . Falling back the boat, you should drive slowly otherwise the boat will not stable. The outboard motor backet can revolve 360. Only in simple let the engine revolve 180 and the operation handle face back, the boat can fall back to drive.
Announcements:
After in the sea water or turbid water cruising
1.Use the fresh water cleaning the outboard motor
2.With the moderate velocity circulating the engine,cool off the water chanel with fresh water.
3.Before completely running out cooling water,don't put the outboard motor outside. Otherwise the water cam pass the exhaust port to enter the air cylinder, from that will cause the engine breakdown.
4.The engine should deposit in the aridity and ventilated well place,avoid exposing directly in the sunshine.
5.Before the long term storing,you should run out of the gasoline in the fuel tank.
Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us).our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!!
About certification:
We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.
SKU:OT-ML-132
Two strokes 3.5 hp and 3.6 hp are controlled by the handle, which is operated by the clutch. There is no Neutral, only idle mode or low speed mode
Product Description
Shipping Weight: 21.4 pounds
MODEL THREE:3.5HP & 2-Stroke (TYPE TWO)
Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us) .our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!!
About certification:
We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.
SKU：OT-ML-279
Two strokes 3.5 hp and 3.6 hp are controlled by the handle, which is operated by the clutch. There is no Neutral, only idle mode or low speed mode
Please Notice:STRICTLY FOR PROFESSIONAL USE ONLY
What you will receive is our new version of this boat engine
The trademark will be Yadao instead of Speeda.
Overall length:92CM
Overall widteh:36.5cm
Overall height:22cm
Transom height:42cm
Full throttle perating range:4000-5000r/min
Maximum output:2.5kw(3.5HP)
Speed:12km/h(four people)
Type:2-stroke
Starting system:Manual start
Staring carburetion system:Choke start]
Propeller mark:7-1/45-A(inch)
The engine and the propeller ratio:2:1
Recommended fuel:Regular unleaded gasoline
Fuel to oil ratio: 35:1 （Please be suject to this version, and disregard the manual about this point）
Gear ratio: 27/13
When at normal cruising,the appearance ofthe seventh picture. Falling back the boat, the appearance of the outboard motor likes theeighth picture . Falling back the boat, you shoulddrive slowly otherwise the boat will not stable. Theoutboard motor backet can revolve 360. Only in
simple let the engine revolve 180 and the operation handle face back,the boat can fall back to drive.
Announcements
After in the sea water or turbid water cruising
1.Use the fresh water cleaning the outboard motor
2.With the moderate velocity circulating the engine,cool off the water chanel with fresh water.
3.Before completely running out cooling water,don't put the outboard motor outside. Otherwise the water cam pass the exhaust port to enter the
air cylinder, from that will cause the engine breakdown.
4.The engine should deposit in the aridity and ventilatedwell place,avoid exposing directly in the sunshine.
5.Before the long term storing,you should run out of the gasoline in the fuel tank.
About certification:
We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.
STRICTLY FOR PROFESSIONAL USE ONLY
Type: 4 stroke 4 horsepower
Capacity: 52cc
Transmission ratio: 2.08 (27:13)
The number of cylinders: 1
MAX SPEED：4500~5500rpm
Maximum power: 2.8 kW /4 HP
Shift position: clutch control
Package volume: 95x40x30 cm
Ignition system: CDI
Cooling system: air cooling
Starting method: Manual start
Refueling: No. 93 gasoline
Propeller size: 7 1/4X7-A
The maximum fuel consumption: 1.4 liters / hour
Recommended Lubricant:4 stroke lubricating oil
Mixing ratio:Pure gasoline
Trim and tilt system:Manual Tilt
Start-In-Gear protection/clutch feature prohibits prop rotation while idling
convenience
Features 360 degree steering rotation for reverse without gear shifting
Cooling system: air cooling
Easy pull off engine cover with push button latch for instant motor access
Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us) .our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!!
About certification:
We can only provide CE certification, there is no other certification can be provided,thanks for your understanding
STRICTLY FOR PROFESSIONAL USE ONLY
Dimension
Overall length 1040mm(40.9 in)
Overall width 872mm(34.3 in)
Overall height 332mm(13.1 in)
Transom height 44CM(17.3 in)
Performance
Full throttle operating range 5000-6000r/min
Maximum output 4.4KW/6HP
Idling speed ( in neutral) 1000±100 r/min
Engine
Gear positions Forward-neutral-reverse
Gear ratio 2.15(28/13)
Trim and tilt system: Manual tilt
Drive unit
Recommended fuel Regular unleaded gasoline
Integral fuel tank capacity 2.5L
Recommended engine oil 2-stroke outboard motor oil
Engine oil type Genuine or recommended 2str engine oil
Lubrication System Engine oil mixed gasoline
Engine oil mixing ratio Fuel 50: Engine oil 1
Gear oil quantity 195ml(6.6 fl.oz.)
Tightening torque for engine
Spark plug 25.0Nm(18.4 ft-lb) (2.55 kgf-m)
Engine oil drain bolt 18.0Nm(13.3 ft-lb) (1.84 kgf-m)
OT-ML-278
Please add gear oil to the gears before use the motor and replace gear oil after the run-in period (10 hours). (If you do not know how to handle this, please contact with us.)
About certification:
We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.
About the noise:
1. All the gasoline machines are noisy, currently we did not test the decibel , but the noise is the same as the motorcycle, so it is a normal phenomenon
2. The machine itself is lightweight, it can use on boat weight of 100kg or less , load-bearing 4 people, but the speed is certainly not the same when one person on it or 4 people on it . Customer who has high expectations on speed, please be noticed.
3. It can be marched with inflatable boats, rubber boats or fishing boats.
4. Necessary: you have to prepare a boat-motor stand or Hanging board on your boat.
Note:
Must read before use!
Four stroke 7 hp:
Firstly, Fill the gear oil (open gear box lid and fill it).
Secondly, Fill NO. 92 petrol, lightly press oil pump 6-10 times.
Thirdly, Fill engine oil don't exceed the head of the pattern.
Forthly, Pull the gear to netural gear, and plug the brake line in, hang the other side of the brake line on your wrist at the same time.
Then, turn the accelerator gets up to 50% and rapidly pull the starter line.
After the motor start , please turn the gear to minimum before put another gear.
Otherwise, the gearwheel will be broken if you put high gear.
Description:
Universal motors, high performance, reliable quality
· Perfect match inflatable boats, fishing boats, sailboats, and small yachts.
· Economical and compact structure. Durable, lightweight and anti-corrosive construction.
· Maneuverable and safe twist grip throttle control.
· Suitable for: Freshwater and saltwater
· One year warranty covers the motor, to provide parts free
Type: 4 stroke 7 horsepower
Capacity: 196CC
Transmission ratio: 2.08 (27:13)
The number of cylinders: 1
Maximum speed: 4500-6000rpm
Maximum power: 5.1 kW /7 HP
Shift position: clutch control
Package volume: 120x60x42.5 cm
Ignition system: TCI
Cooling system: air cooling
Starting method: hand start
Refueling: No. 93 gasoline
Propeller size: 3-7 1/2''x5''
Gear position: F-N-R
Control system: Tiller control
N.W./G.W.: 26.7/31.7kgs
Recommended Lubricant: 4 stroke lubricant oil
Trim and tilt system: Mannual tilt
Standard fuel tank capacity: 1.4L/within
long shaft ：50.8CM
Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us) .our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!!
About certification:
We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.
Brand: HANGKAI
Displacement: 123CC
Gear ratio: 2.08(27:13)
Cylinder: 1
Max.Output(kw): 4.8
Max.speed(r/min): 5000-6000
Gear Positions: F-N-R
Packing size: 114x64x41cm
Ignition System: CDI
Cooling System: Water-cooling
Control System: Tiller control
Starting System: Manual start
Control System: #93 gasoline
N.W./G.W.(kgs): 26/31.2
Bore x Stroke(mm): 59x45
Recommended Propeller range: 3 -7"x9"
Recommended Lubricant: Four Stroke Lubricating oil
Mixing ratio: Pure gasoline
Trim and tilt system: Manual Tilt
Overall LxWxH(cm): 78.3x34.3x103.9
Standard fueel tank capacity: 12L
Optional fuel tand capacity: /
Bonus accessories:
brochures, tubing, cotter pins
Pump impeller, start rope, start key
12 liter fuel tank, tool kit, spark plug, cylinder head pad
Must Read before using!
Two stroke 12 hp:
Firstly, Fill the gear oil (open gear box lid and fill it).
Secondly, Fill NO. 92 petrol, lightly press oil pump 6-10 times.
Thirdly, Fill engine oil don't exceed the head of the pattern.
Forthly, turn the throttle to the start up and turn the accelerator gets up to 50%.
Then, Rapidly pull the starter line.
After the motor start, please turn the throttle to running state.
Then, it can be operated now.
Don't do the following will avoid cylinder Scoring:
1，start the motor in the water
2, use the motor when it stop cyling water
Even if you want test the motor, it should be done in the river!
When there is no water coming out from the motor,please stop using it immediately ,then check the impeller of Water pump or check if the water outlet has been blocked.
About certification:
We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.
Several issues with this motor first the linkage that goes from the gear selector to the starting rope to block the rope to be pull when the motor is in gear was unattached , and still after fixing it every time you go into any gear it gets unattached second, the starting rope doesn't retract all the way when you attend to start the engine
Brand: HANGKAI
Displacement: 169CC
Gear ratio: 2.08(27:13)
Cylinder: 2
Max.Output(kw): 8.8
Max.speed(r/min): 4500-5500
Gear Positions: F-N-R
Packing size: 120x70.5x37.5cm
Ignition System: CDI
Cooling System: Water-cooling
Control System: Tiller control
Starting System: Manual start
Control System: #93 gasoline
N.W./G.W.(kgs): 27/31
Bore x Stroke(mm): 50x43
Recommended Propeller range: 3 -9"1/4''x8"
Recommended Lubricant: 2 Stroke Lubricating oil
Mixing ratio: Fuel:oil=50:1
Trim and tilt system: Manual Tilt
Overall LxWxH(cm): 78.3x33.2x104
Standard fuel tank capacity: 24L
- We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them!
