Stock # 130

This item is pre-owned – it will work like new once programmed to your vehicle

 

One (1)

O.E.M. Original Equipment Manufacturer Factory

 remote keyless entry fob alarm

Transmitter control clicker keyfob controller replacement

Functions at 100% Tested & Guaranteed
Item #: 130
PRE-OWNED
FCC ID: GQ43VT14T
Replaces Toyota OEM 89742-AA020 (89742AA020)
Part #: 89742-06010 (8974206010)
TRW 88LPOO65 (88LP0065) RSS-210 DENSO
CANADA: 1470 102 849 (1470102849)
Canada/Mexico Part #: CONDITION: GOOD
MEX: RCPTR3002-028 (RCPTR3002028)
Reg. Price: $130.00

 3 BUTTONS: LOCK UNLOCK PANIC

 BEFORE YOU BUY PLEASE READ…

Please remember to check out the programming requirements

 This is a USED Factory Original Equipment O.E.M. keyless remote control transmitter.

keyless remote control transmitter.

Remote / Battery Specifications
LED LightNone
Condition:Pre-Owned
Battery:
Yes, Installed
Required batteries::

1: CR2032
Buttons: 3: Lock, Unlock, Panic (on back)
Frequency: 315 MHz (315MHz)

 

Please Note:

 

This is the remote for the FACTORY INSTALLED RKE system. Your car may have the optional, Toyota VIP

or RS3200 RKE system installed. This remote will ONLY work with the FACTORY INSTALLED RKE System.

Compatible Vehicles*:

 

2002 2003 2004 2005 2006 2007 2008 Pontiac Vibe

1999 2000 2001 2002 2003 2004 2005 Toyota Camry

2000 2001 2002 2003 2004 2005 Toyota Celica

2001 2002 2003 2004 2005 2006 2007 2008 Toyota Corolla

2000 2001 2002 2003 2004 2005 Toyota Echo

2003 2004 2005 2006 2007 2008 Toyota Matrix

1999 2000 2001 2002 2003 Toyota Sienna

1999 2000 2001 2002 2003 Toyota Camry Solara

 

*All vehicles with factory installed Remote Keyless Entry (RKE).

 

MAKE/MODEL

YEARS

Toyota CELICA

PROGRAMMING:

1. Start with key out of ignition, drivers door is open all others closed and  drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert key into ignition(Do NOT Turn) Pull key out.
    B. Insert key into ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open drivers door.
    B. Close then open drivers door.
    C. Insert key into ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open drivers door.
    B. Close then open drivers door.
    C. Insert key into ignition & leave it in ignition.
    D. Close drivers door.
    E. Turn ignition to ON (Do NOT Start) then back to OFF.
    F. Remove key from ignition.

5. Within 3 seconds, power door locks should lock then unlock automatically
    indicating successful entry into program mode.
    Return to step 1 if locks don’t cycle @ this point.

6. Perform these steps within 40 seconds.
    A. Press lock & unlock buttons on remote simultaneously for 1.5 seconds.
    B. Immediately after letting go of lock & unlock buttons,
        Press lock button by itself and hold for 2 seconds. Within 3 seconds, door locks should lock & then unlock once indicating successful programming. If door locks cycle twice, repeat steps A & B in step 6 as remote wasn’t accepted.
    C. Repeat steps A & B in step 6 for each new remote.

7. Open drivers door.

 2000 2001 2002 2003 2004 2005

00 01 02 03 04 05

All Models With Keyless Entry

Toyota CAMRY

PROGRAMMING INSTRUCTIONS 1999

Programming: please not a maximum of 2 remotes can be programmed at once.

Programming remote erases all previous codes. All remotes must be programmed at the same time.

 

~ Can be used when adding or replacing transmitter or when your system malfunctions

 

-          Remove KEY FROM IGNITION SWITCH

-          Disconnect door mirror adjustment switch harness multi-plug

-          Jump door mirror adjustment switch harness multi-plug terminals 2 & 10----- and then

-           ----- SYSTEM SHOULD NOW LOCK & UNLOCK THE AUTOMOBILE. Once.

-          Push any remote button------

-          ------ SYSTEM SHOULD NOW LOCK & UNLOCK THE AUTOMOBILE to confirm.

-          If required repeat button procedure to program a 2nd remote---

-          SYSTEM SHOULD NOW LOCK & UNLOCK THE AUTOMOBILE to confirm

-          To exit programming mode------

-          ------ Remove jump lead from door mirror adjustment switch harness multi-plug

-          Refit all components in reverse order of removal.

PROGRAMMING INSTRUCTIONS 2000-2005

1. Start with the key out of the ignition, drivers door is open all others closed and  drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert key into ignition (Do NOT Turn) Pull key out.
    B. Insert key into ignition (Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert key into ignition (Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the driver’s door.
    E. Turn ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, power door locks should lock then unlock automatically indicating successful entry into programming mode.   Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press lock & unlock buttons on remote simultaneously for 1.5 seconds.
    B. Immediately after letting go of lock & unlock buttons,
        Press lock button by itself & hold for 2 seconds. Within 3 seconds, door locks should lock and then unlock once indicating successful programming. If door locks cycle twice, repeat steps A & B in step 6 as remote was  not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

1999 2000 2001 2002 2003 2004 2005

99 00 01 02 03 04 05

All Models With Keyless Entry

 

Toyota COROLLA

PROGRAMMING INSTRUCTIONS

1. Start with the key out of the ignition, drivers door is open all others closed and  drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert key into ignition (Do NOT Turn) Pull key out.
    B. Insert key into ignition (Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert key into ignition (Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the driver’s door.
    E. Turn ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, power door locks should lock then unlock automatically indicating successful entry into programming mode.   Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press lock & unlock buttons on remote simultaneously for 1.5 seconds.
    B. Immediately after letting go of lock & unlock buttons,
        Press lock button by itself & hold for 2 seconds. Within 3 seconds, door locks should lock and then unlock once indicating successful programming. If door locks cycle twice, repeat steps A & B in step 6 as remote was  not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

2001 2002 2003 2004 2005 2006 2007 2008

01 02 03 04 05 06 07 08

All Models With Keyless Entry

Toyota CAMRY SOLARA SOLARO

PROGRAMMING INSTRUCTIONS

1. Start with the key out of the ignition, drivers door is open all others closed and  drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert key into ignition (Do NOT Turn) Pull key out.
    B. Insert key into ignition (Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert key into ignition (Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the driver’s door.
    E. Turn ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, power door locks should lock then unlock automatically indicating successful entry into programming mode.   Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press lock & unlock buttons on remote simultaneously for 1.5 seconds.
    B. Immediately after letting go of lock & unlock buttons,
        Press lock button by itself & hold for 2 seconds. Within 3 seconds, door locks should lock and then unlock once indicating successful programming. If door locks cycle twice, repeat steps A & B in step 6 as remote was  not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

1999 2000 2001 2002 2003

99 00 01 02 03

All Models With Keyless Entry

Toyota SIENNA

PROGRAMMING INSTRUCTIONS

1. Start with the key out of the ignition, drivers door is open all others closed and  drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert key into ignition (Do NOT Turn) Pull key out.
    B. Insert key into ignition (Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert key into ignition (Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the driver’s door.
    E. Turn ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, power door locks should lock then unlock automatically indicating successful entry into programming mode.   Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press lock & unlock buttons on remote simultaneously for 1.5 seconds.
    B. Immediately after letting go of lock & unlock buttons,
        Press lock button by itself & hold for 2 seconds. Within 3 seconds, door locks should lock and then unlock once indicating successful programming. If door locks cycle twice, repeat steps A & B in step 6 as remote was  not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

1999 2000 2001 2002 2003

99 00 01 02 03

All Models With Keyless Entry

Toyota ECHO

PROGRAMMING INSTRUCTIONS

1. Start with the key out of the ignition, drivers door is open all others closed and  drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert key into ignition (Do NOT Turn) Pull key out.
    B. Insert key into ignition (Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert key into ignition (Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the driver’s door.
    E. Turn ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, power door locks should lock then unlock automatically indicating successful entry into programming mode.   Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press lock & unlock buttons on remote simultaneously for 1.5 seconds.
    B. Immediately after letting go of lock & unlock buttons,
        Press lock button by itself & hold for 2 seconds. Within 3 seconds, door locks should lock and then unlock once indicating successful programming. If door locks cycle twice, repeat steps A & B in step 6 as remote was  not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

2000 2001 2002 2003 2004 2005

00 01 02 03 04 05

All Models With Keyless Entry

Toyota MATRIX

PROGRAMMING INSTRUCTIONS

1. Start with the key out of the ignition, drivers door is open all others closed and  drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert key into ignition (Do NOT Turn) Pull key out.
    B. Insert key into ignition (Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert key into ignition (Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the driver’s door.
    E. Turn ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, power door locks should lock then unlock automatically indicating successful entry into programming mode.   Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press lock & unlock buttons on remote simultaneously for 1.5 seconds.
    B. Immediately after letting go of lock & unlock buttons,
        Press lock button by itself & hold for 2 seconds. Within 3 seconds, door locks should lock and then unlock once indicating successful programming. If door locks cycle twice, repeat steps A & B in step 6 as remote was  not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

2003 2004 2005 2006 2007 2008

03 04 05 06 07 08

All Models With Keyless Entry

 

Pontiac VIBE

 

PROGRAMMING INSTRUCTIONS

1. Start with the key out of the ignition, drivers door is open all others closed and  drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert key into ignition (Do NOT Turn) Pull key out.
    B. Insert key into ignition (Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert key into ignition (Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the driver’s door.
    B. Close then open the driver’s door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the driver’s door.
    E. Turn ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, power door locks should lock then unlock automatically indicating successful entry into programming mode.   Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press lock & unlock buttons on remote simultaneously for 1.5 seconds.
    B. Immediately after letting go of lock & unlock buttons,
        Press lock button by itself & hold for 2 seconds. Within 3 seconds, door locks should lock and then unlock once indicating successful programming. If door locks cycle twice, repeat steps A & B in step 6 as remote was  not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

2002 2003 2004 2005 2006 2007 2008 2009

02 03 04 05 06 07 08 09

All Models With Keyless Entry

 

All of our keyless remotes are listed just as the manufacturer states for make model & year compatibility  -

 **SOME VEHICLES HAVE KEYLESS SYSTEMS INSTALLED THAT HAVE STANDARD PACKAGES & SOME ARE OPTIONAL (DEALER INSTALLED)

**(this can change what remote FCC ID &/or part will be compatible with your system)

** WE ASK THAT YOU VERIFY w/ A DEALER PRIOR TO PURCHASE AS TO WHAT FCC ID # YOU NEED FOR YOUR VIN

 

STOP!

 Before You Buy Please Read…

 

Program Remote To Your Vehicle

If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.

This remote needs to be programmed to your vehicle in order for it to work with your vehicle’s installed RKE (remote keyless entry ) system:

1.   Some years require diagnostic programming according to how the manufacturer set the system

         a.   Free programming Requirements per manufacturer upon request

         b.  Contact  us via  eBay messages (Keyless4u store) Prior to Purchase  

with  your vehicle’s ….

1.  Make

2.  Model

3.  Year

2.  We will respond via eBay messages with the manufacturer’s programming requirements so that you can determine if you are capable of programming your vehicle or if you will need to visit a local dealer or locksmith for programming with a diagnostic scan tool – we do not write the programming – we pass it on to you as a courtesy.

How to find out if this remote is compatible with your Vehicles’ installed RKE System

If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.

1.   Check the back of your current or old keyless remote to match FCC ID /Part #’s.

2.   Contact your local dealer and tell them your VIN# and ask what part # / FCC ID you need.

Your vehicle will be installed with one of the following keyless entry systems:  

  a. Standard Keyless Remote Packages: Installed at time of manufacture. 

  b. Optional Keyless Remote Packages: Installed by a dealer. 

  c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. 

  d. No remote keyless entry system at all.

The above information can change which remote you need
for your installed remote keyless system.

 

Australian Customers: The frequency of our remotes typically do not match the frequency needed for Australian Model Remotes. Please verify that this remote will work for your vehicle prior to purchase.

 

Payment:  We accept payment via PayPal or Credit Card. Please contact us via eBay messages for any questions concerning payments.  Payment is expected within 5 days

PA SALES TAX:  As per the State of PA Franchise Board we must collect sales tax from PA Residents for any purchase made from our store.

Contact/Email: Due to scams etc, we DO NOT respond to emails. We only read/respond to EBAY MESSAGES. Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. Please contact us with questions via eBay messages (keyless4u).

 

100% Guarantee Remote Shipping / Return Policy

Shipping & Handling

Combined Shipping & Handling Discount (multiple item purchase discount):

S&H discount = the price of the 1ST remote’s S&H  + 1.99 each additional remote’s  S&H 

Shipped From: Pennsylvania, USA

Shipping Method: USPS mail service

USA Shipment Options:

   ◊ USPS 1ST class mail service

   ◊ USPS Priority class mail service

   ◊ USPS EXPRESS class mail service

Canadian Shipment Options:

   ◊ USPS 1ST class mail service

   ◊ USPS Priority class mail service

   ◊ USPS Express class mail service

Worldwide (Outside of  USA & Canada) Shipment Options:

   ◊ USPS Priority class mail service

   ◊ USPS Express class mail service

Australian Customers: The frequency of our remotes typically do not match the frequency needed for Australian Model Remotes. Please verify that this remote will work for your vehicle prior to purchase.

 

Warranty/Returns:  

1.     We have a 30 day return policy. 

2.     All returns for replacements and refund need an RMA #.

3.     Please contact us before returning items so we can give you the RMA # and the proper return address.

4.     No refunds / replacements will be granted without an RMA#

5.     All cut keys are subject to a $20 deduction from the refund

 

We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged.

Please Note: Each remote and circuit board is UV id’d prior to shipment  – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement.

 

  Does this keyless remote entry come with a battery?  

Yes. It will have a working battery installed.

Battery Condition:

        A. All remotes sold on Keyless4u include working batteries.

        B. Installed batteries are not tested for battery life- they are simply working.

             Some are new and some are used.

 


WORD KEY: