LEXUS GS300/430 FACTORY STYLE SPOILER 2006+ Brand New Factory Style Spoiler for 2006+ Lexus GS series. This spoiler comes painted to match your car. Spoiler is painted with Dupont factory matched OEM paint and comes with a 3 year warranty. Please select your paint code from below and note the paint code when ordering. Please email any questions. See picture for more details.
THE COLORS WE HAVE AVAILABLE ARE: 202 - Black 062 - Crystal White * If you do not see your color code listed above, please contact us
Made from Blow-Molded ABS Lightweight and won't crack like fiberglass Mounting hardware, installation instructions, and template included. Will ship to Alaska, Hawaii, Canada, Puerto Rico, and Puerto Rico. Please choose International Shipping charge of $50.00 when making payment.
Bolt-On Application STEP-by-STEP STEP 1.
After opening and inspecting your rear spoiler you can begin the installation. Notice that the LED light and the pedestal gaskets come pre-installed from the factory (pre-painted spoilers only), which will shave some time off the installation. STEP 2.
Start out by turning over the spoiler and setting it on a soft surface, to prevent any scratches. Place the plastic locator T-strips into the mounting holes on spoiler and LED brake light hole. TIP: A small piece of masking tape is helpful in holding the T-strips in position. STEP 3.
Place spoiler on closed decklid and align to proper position. A measuring tape will ensure a "perfect" alignment. STEP 4.
Using masking tape, secure locator T-strips to the decklid of the vehicle. Simply remove the spoiler by lifting straight up leaving the T-strips secured to the decklid. STEP 5.
Using a 1/8" drill bit, drill thru the T-strip holes and into the decklid. It is not necessary to drill through a double panel on this particular application because we can utilize the factory openings on the underside. STEP 6.
Remove T-strips and using a 5/16" drill bit, drill thru the 1/8" hole in step 5. If a "double panel" does exist, use a 3/4" drill bit to drill thru the "inner panel". This allows the ratchet or nutdriver to secure the screw tightly against the upper panel. STEP 7.
After deburring all holes, apply small amounts of primer which will help prevent rusting of the freshly drilled metal. STEP 8.
Pull back pedestal gaskets exposing mounting tape and place spoiler on decklid and using supplied screws secure to the vehicle using a ratchet or nutdriver. Be sure to feed the LED light wire through the pre-determined hole. Apply small amounts of silicone based caulk over mounting screws as this will help prevent leaking, rusting, or loosening of screws. TIP: Gasket material is extremely sticky once exposed, so we found that spraying it with water or glass cleaner will allow you to reposition spoiler as needed. STEP 9.
When installing a LED brake light it is recommended to splice into the 3rd brake light in the vehicle and attach spoiler wires using electrical tape. Step on the brake light to ensure proper wiring, simply switch the two connections if spoiler does not light. STEP 10.
Finish your install by vacuuming any debris or metal shavings and then reinstall any panels, mats or other items that may have removed earlier in installation.
No Drill Application STEP-by-STEP Step 1. Surface Cleaning
Clean surface area that is to be covered by spoiler thoroughly, with Isopropyl Alcohol. Step 2. Test Fitting the Unit
Before removing the tape backing, test fit spoiler in order to get comfortable with the placement. You can mark the position with a grease pen or masking tape for a perfect fit. Step 3. Preparation
Peel back the corner of the red liner on the 3M tape and remove all pieces, avoid touching exposed tape. Step 4. Installation
Gently press spoiler into place on the deck lid, hatch or rear glass. Once satisfied with placement, firmly press down on spoiler to ensure cohesion along entire vehicle surface. Continue to apply pressure or use masking tape to keep unit from lifting. Helpful Tips
Adhesive silicone and/or adhesion promoters are often used in conjunction with provided 3M tape for long lasting durability. For best results installation should be conducted in temperatures above 72. Refer to tape manufacturers recommendations for full details. Do Not clean, wash, wax or drive for 12 hours after installation. Shopitall is not responsible for no drill attachment durability.
| 
