This is a Factory Original Equipment O.E.M.
keyless remote control transmitter.

Remote / Battery Specifications

Condition:	NEW
Battery:	Yes, Installed
Buttons:	4: Lock, Unlock, Rear Power Window, Panic (on back)
Required Batteries:	1: CR2016
Frequency:	315 MHz
Please Note:	This is the remote for the FACTORY INSTALLED RKE system. Your car may have the optional, Toyota VIP or RS3200 RKE system installed. This remote will ONLY work with the FACTORY INSTALLED RKE System.
Compatible Vehicles*:	2005 2006 2007 2008 2009 Toyota 4 Runner 2004 2005 2006 2007 2008 Toyota Sequoia 2004 Toyota Highlander 2004 2005 Toyota Rav4
	*All vehicles with factory installed Remote Keyless Entry (RKE).

All of our keyless remotes are listed just as the manufacturer states for make model & year compatibility -

**SOME VEHICLES HAVE KEYLESS SYSTEMS INSTALLED THAT HAVE STANDARD PACKAGES & SOME ARE OPTIONAL (DEALER INSTALLED)

**this can change what remote FCC ID &/or part will be compatible with your system

** WE ASK THAT YOU VERIFY w/ A DEALER PRIOR TO PURCHASE AS TO WHAT FCC ID # YOU NEED FOR YOUR VIN

MAKE/MODEL

YEARS

Toyota 4runner 4 runner (05-08) / SEQUOIA (06-08)

TOYOTA 4RUNNER

Programming~ please note a maximum of 4 remotes can be programmed at once.

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.

3. Perform these steps within 40 seconds.
    A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
        starting with lock. Use an even pace and try to go about one cycle per second.
        (1Cycle = 1 lock and 1 unlock).
    B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
    A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
        starting with lock. Use an even pace and try to go about one cycle per second.
         (1Cycle = 1 lock and 1 unlock).
    B. Insert the key in the ignition cylinder.
    C. Turn the ignition to ON (Do NOT Start) then back to OFF.
    D. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful
entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
    B. Immediately after letting go of the lock and unlock buttons, press the lock button by
        itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
        indicating successful programming. If the door locks do not cycle, or cycle twice.
        repeat steps A and B in step 6 as your remote has not been accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Close drivers door.

2005 -2006 2007 2008 2009

05 06 07 08 09

All Models With Keyless Entry

All of our keyless remotes are listed just as the manufacturer states for make model & year compatibility -

SOME VEHICLES HAVE KEYLESS SYSTEMS INSTALLED THAT HAVE STANDARD PACKAGES & SOME ARE OPTIONAL (DEALER INSTALLED)

**(this can change what remote FCC ID &/or part will be compatible with your system)

** WE ASK THAT YOU VERIFY w/ A DEALER PRIOR TO PURCHASE AS TO WHAT FCC ID # YOU NEED FOR YOUR VIN

If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.

This remote needs to be programmed to your vehicle in order for it to work with your vehicle’s installed RKE (remote keyless entry ) system:

1. Some years require diagnostic programming according to how the manufacturer set the system

2. We will respond via eBay messages with the manufacturer’s programming requirements so that you can determine if you are capable of programming your vehicle or if you will need to visit a local dealer or locksmith for programming with a diagnostic scan tool – we do not write the programming – we pass it on to you as a courtesy.

How to find out if this remote is compatible with your Vehicles’ installed RKE System

If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.

1. Check the back of your current or old keyless remote to match FCC ID /Part #’s.

2. Contact your local dealer and tell them your VIN# and ask what part # / FCC ID you need.

c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop.

The above information can change which remote you need
for your installed remote keyless system.

Australian Customers: The frequency of our remotes typically do not match the frequency needed for Australian Model Remotes. Please verify that this remote will work for your vehicle prior to purchase.

Payment: We accept payment via PayPal or Credit Card. Please contact us via eBay messages for any questions concerning payments. Payment is expected within 5 days

PA SALES TAX: As per the State of PA Franchise Board we must collect sales tax from PA Residents for any purchase made from our store.

Contact/Email: Due to scams etc, we DO NOT respond to emails. We only read/respond to EBAY MESSAGES. Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. Please contact us with questions via eBay messages (keyless4u).

S&H discount = the price of the 1^ST remote’s S&H + 1.99 each additional remote’s S&H

3. Please contact us before returning items so we can give you the RMA # and the proper return address.

We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged.

Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement.

B. Installed batteries are not tested for battery life- they are simply working.