Click on the thumbnails to supersize

Item Description

NOTE: These covers will only fit the seat style as pictured above and are NOT custom. If your vehicle is listed in the compatibility section above, please be aware this only states that these seat covers MAY work for your vehicle IF you have the seat type and measurements that are shown above (Please also see "Important Part Details" next to your vehicle Compatibility search). Many vehicles will have more than one seat type that comes standard in the same year, make, and mode. To ensure a proper fit, please read the provided details and measurements in our item page description to help ensure these seat covers will accommodate the seat type in your vehicle. If your seat type is Not as pictured above, these seat covers Will Not work for you. If you have questions concerning fit please contact us via eBay or you can telephone us with the number on our about me page

FABRIC: Synthetic Leather similar to vinyl but softer than vinyl, with thin foam type backing (not as thick as genuine leather or vinyl) on seating area of seat covers. Front buckets will have a 3/4 to full stretchy polyester backside, depending on the height of the seat (the part you see from the rear seat of the vehicle) that will help conform the seat cover to the molds of the seats (if you have pockets located on the backside of your seats, they will be covered with these seat covers in place). Both pieces of The FREE rear bench will be trimmed in the same polyester for added conformation. Floor mats are carpeted with bright plastic Red Dragon design on Both front floor mats (see close up above) and an Anti-Slip ribbed tip backing.

INSTALLATION: These seat covers slip over your existing factory seats and fasten underneath the seat with pre-sewn elastic straps and S-hooks. You may adjust these straps as needed for a more custom look.

Head rest removal is recommended to install these seat covers. The difficulty of this seat cover package to install depends on the ease at which your head rests are removed and on the access that you have behind and beneath your seats.

Note: Please contact a technician before removing head rests that have wires attached.

PLEASE NOTE:Where these seat covers are NOT custom, they will not feature accommodations for some seat controls, levers, or bolsters depending on the location of these features, modifications may be needed. These features will also limit the access under the seat, which may make installation more difficult. (Please make sure your driver's side and passenger's side seat areas on your front row seats are the same size). These seat covers are NOT recommended for front row seats with Side Seat Airbags or Fold down armrests, if applicable.

COLOR: Red and Black

INCLUDED IN THIS PACKAGE: 2 standard low back seat covers with 2 matching head rest covers for front buckets, 1 steering wheel cover (made to accommodate standard size steering wheels that are 14-1/2 to 15 inches in diameter), 2 seat belt shoulder pads, 2 front standard cut floor mats, 2 rear standard cut floor mats, and a FREE 2-piece standard rear bench (one piece will wrap the back part of the bench seat and the other piece will wrap the seat area) and 2 head rest covers for your rear bench seat cover.

FREE Bench Seat Cover Details: Our bench seat cover, included in this package for FREE, will come in 2 pieces, 1 piece will wrap the backrest portion of the bench seat as one unit and the 2nd piece will wrap the seat cushion area as one unit. Because of the 2 piece design this bench cover will fit most standard benches (please see bench seat type and Measurements shown above). Because this is a universal bench, it will not have a full backside (the part you see from the rear window). Some rear benches will need to be removed for installation.

PLEASE NOTE: If your bench seat is Smaller that 54-55 inches in length and Shorter than 31 inches in height, The excess Fabric will need to be wrapped behind and beneath your bench seat by connecting the installation straps to each-other on the back side of the bench. The difficulty of this bench seat cover to install will depend on the access behind and beneath your seat. Some Benches will need to be removed for installation.

This bench seat cover best accommodates bench seats without any type of head rests or with head rests that may be removed. We recommend removing your bench seat head rests, if applicable, before installing the back rest seat cover portion of your bench. After your bench seat cover is installed, you are able to make tiny X's in the seat cover to re-insert your head rest posts.

BENCH BACKREST MEASUREMENTS:The bench seat backrest cover is approximately 54-55 inches in length and 30-31 inches in height and will have 5 inches of stretchy polyester on the 2 outer edges with alternating Red and Black Panels lining up vertically in-between (when installed this polyester trim will be on the sides of the seat closest to the doors of the bench seat backrest).

BENCH SEAT CUSHION MEASUREMENTS:The bench seating area cover is approximately 54-55 inches in length and 22-23 inches wide and will have 5 inches of stretchy polyester on 3 sides (when installed this polyester trim will be on the sides of the seat closest to the doors and the seat front edge) and will have alternating Red and Black Panels lining up in-between.

IMPORTANT FREE BENCH INFORMATION!: Split bench functionality and/or fold down arm rest functionality, if applicable, will be lost with our FREE standard bench seat cover in place. These seat covers will cover your entire bench seat as one unit with your arm rest folded in the upright position along with the back of your seat. Most bench seats will have the seat belts exiting through the crease where the backrest of the seat meets the seat cushion area at the back of the seat, and do not require ready made openings for the seat belts. Because seat belt openings may vary in location on the rear bench our standard universal design bench seat covers will not feature pre-made openings. However, the material is guaranteed not to fray or tear when cut for openings (as long as cut is not made on a seam, or stretchy polyester material). Please make sure seat covers are satisfactory before making any modifications, as modified covers cannot be returned for a refund. The functionality of the seat-belts shouldn't be lost with this bench seat cover installed on the seat if installed properly.

STEERING WHEEL COVER INSTALLATION: To make your steering wheel cover more pliable during installation, we recommend that that you warm it. This should help make it a little more flexible for installation. Also, to aid in the installation, insert a flat, dull-edged object (such as butter knife or a bicycle tire changing tool) between the cover and steering wheel and slide the tool along the edge. (Unfortunately if your steering wheel is greater than 15 inches in diameter, this cover will not fit.) You will want a snug fit with your steering wheel cover in place. If the steering wheel cover is loose it may slip while driving.

IMPORTANT FLOOR MAT INFORMATION:These floor mats are NOT Custom OEM floor mats. These are standard fit floor mats with the dimension shown above. The floor mats are one solid piece and do NOT feature an opening for the clip (grommet) which some vehicles will feature to help hold the driver's side floor mat in place. If your vehicle features this grommet you are able to make a small opening in the floor mat so that you are able to hook it into place using this clip. Please make sure mats are satisfactory before making any modifications, as modified mats and seat covers cannot be returned for a refund.