Stock # 115 C

This item is pre-owned – it will work like new once programmed to your vehicle

Buttons are faded and there are chips in the casing

One (1)

O.E.M. Original Equipment Manufacturer Factory

 remote keyless entry fob alarm

Transmitter control clicker keyfob controller replacement

Functions at 100% Tested & Guaranteed

Item #: 115
PRE-OWNED
FCC ID: KOBUT1BT, KOBUTIBT
Part #: GM 25678792, GM25678792
Compatible part numbers:  25665574, 25665575, 25668603 25628814
Canada/Mexico Part #:  1983 101 393, 1983101393

 

 

 
BEFORE YOU BUY PLEASE READ……

This is a USED Factory Original Equipment O.E.M.

Keyless remote control transmitter

Remote / Battery Specifications
Condition:Pre-Owned
Battery:Yes, Installed
Buttons: 4: Lock Door, Unlock, Panic, Trunk Release

Required

Batteries:

1: CR2032 

Frequency: 315MHz (315 MHz)

Compatible

Vehicles*:         

 

1996 1997 1998 1999 Buick LeSabre

1996 1997 1998 1999 Buick Park Avenue

1999 Buick Riviera

2000 Chevy Impala

2000 Chevy Malibu

2000 Chevy Monte Carlo

1999 2000 Oldsmobile Alero

1996 1997 1998 1999 Oldsmobile Aurora

1996 1997 1998 1999 Oldsmobile Eighty-Eight 88

1996 1997 1998 1999 Oldsmobile LSS

1996 Oldsmobile Ninety-Eight 98

1997 1998 1999 Oldsmobile Regency

1996 1997 1998 1999 Pontiac Bonneville

2000 Pontiac Grand Am


 

MAKE/MODEL

YEARS

Buick Park Avenue Ave Ultra

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

PROGRAMMING INSTRUCTIONS

1.      Insert keys in ignition and leave in the OFF position.

2.      Locate the OBDII  Port.

3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 and 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure).  Make sure you know which terminals are 8 and 4. The vehicle will respond by locking then unlocking the doors to signify entering of programming mode.

4.   Close Doors 

5.      Turn ignition to the ON position (as far as you can go without cranking the engine). Doors will lock.      

6.    Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. Up to about 30 seconds, the vehicle will respond by locking then unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitter (if any – including any existing remotes).

8.   Remove jumper wire applied to the OBDII Port

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

Buick LeSabre Le Sabre

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

PROGRAMMING INSTRUCTIONS

 

1.      Insert keys in ignition and leave in the OFF position.

2.      Locate the OBDII  Port.

3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 and 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure).  Make sure you know which terminals are 8 and 4. The vehicle will respond by locking then unlocking the doors to signify entering of programming mode.

4.   Close Doors 

5.      Turn ignition to the ON position (as far as you can go without cranking the engine).

      Doors will lock.      

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. Up to about 30 seconds, the vehicle will respond by locking then unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitter (if any – including any existing remotes).

1.       8.   Remove jumper wire applied to the OBDII Port

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

Buick Riviera

O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

 

PROGRAMMING INSTRUCTIONS

1. Insert keys in ignition and leave in the OFF position.

2.      Locate the OBDII  Port.

3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 and 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure).  Make sure you know which terminals are 8 and 4. The vehicle will respond by locking then unlocking the doors to signify entering of programming mode.

4.   Close Doors 

5.      Turn ignition to the ON position (as far as you can go without cranking the engine).

      Doors will lock.      

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. Up to about 30 seconds, the vehicle will respond by locking then unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitter (if any – including any existing remotes).

8.   Remove jumper wire applied to the OBDII Port.

1999

99

All Models With Keyless Entry

O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

 

Pontiac Bonneville Boneville

SLE  SSEi

 

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

 

1. Insert keys in ignition and leave in the OFF position.

2. Locate the OBDII Port under drivers side dashboard.
Note port is wider at top: Your OBDII Port will not have numbers, use this for reference.
        
3. Make sure there are metal contact pins in terminals 8 and 4. connect 8 and 4
    with a suitable jumper wire (leave jumper wire connected throughout the
    programming procedure.) Make sure you know which terminals are 8 and 4.
    The vehicle will respond by locking and unlocking the doors to signify entering
    of programming mode.
   

4. Close doors.

5. Turn ignition to the ON position ( as far as you can go without cranking the 
    engine ). Doors will lock.

6. Press and hold both the LOCK and UNLOCK buttons together on the first
    remote to be programmed, up to 30 seconds, the vehicle will respond by
    locking then unlocking  the doors. Release buttons.

7. Within one minute, repeat step 6 for any additional remotes if any, including
    existing remotes.

8. Remove jumper wire from OBDII Port.

9. Test Remote(s).

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

 

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

Pontiac GRAND AM

 

needs diagnostic programming from locksmith or local dealer

the manufacturer’s programming instructions For your vehicle make model and year specify diagnostic programming required

                                                    

This keyless entry requires programming by your local dealer or locksmith. The procedure takes a few seconds to complete so many dealers will do it as a courtesy. If your dealer does charge a fee, local locksmiths usually charge much less.

 

You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment

2000

00

  remote system changed mid-year 1999.  Early 99 takes different

All Models With Keyless Entry

O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

Olds Oldsmobile Aurora

 

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

 

needs diagnostic programming from locksmith or local dealer

the manufacturer’s programming instructions For your vehicle make model and year specify diagnostic programming required

                                                    

This keyless entry requires programming by your local dealer or locksmith. The procedure takes a few seconds to complete so many dealers will do it as a courtesy. If your dealer does charge a fee, local locksmiths usually charge much less.

 

You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

 

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

Olds Oldsmobile EIGHTY-EIGHT 88

O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

 

programming

1.   Insert key in ignition and leave in the OFF position

2.    Locate the Data Link Port. It is located under dash drivers side. Be sure you know
      which pins are 8 and 4.   

      (Note port is wider at top) Your OBDII port will not
           have numbers, use this diagram for reference. 

  

    3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a 
        suitable jumper wire (leave the jumper wire connected throughout the programming
        procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond
        by locking and unlocking the doors to signify entering of programming mode.


4.    Close doors.

5.   Turn ignition to the ON position (as far as you can go without cranking the engine).
      Doors will lock. 

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to
       be programmed. After about 15 seconds, the vehicle will respond by locking and
       unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitters to be
       programmed.

8.    Remove jumper wire applied to th OBDII Port

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

 

Olds Oldsmobile NINETY-EIGHT 98

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

 

programming

1.   Insert key in ignition and leave in the OFF position

2.    Locate the Data Link Port. It is located under dash drivers side. Be sure you know
      which pins are 8 and 4.   

      (Note port is wider at top) Your OBDII port will not
           have numbers, use this diagram for reference. 

  

   
3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a 
        suitable jumper wire (leave the jumper wire connected throughout the programming
        procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond
        by locking and unlocking the doors to signify entering of programming mode.


4.    Close doors.

5.   Turn ignition to the ON position (as far as you can go without cranking the engine).
      Doors will lock. 

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to
       be programmed. After about 15 seconds, the vehicle will respond by locking and
       unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitters to be
       programmed.

8.    Remove jumper wire applied to th OBDII Port

1996

96

All Models With Keyless Entry

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

 

Olds Oldsmobile ALERO

O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

 

needs diagnostic programming from locksmith or local dealer

the manufacturer’s programming instructions For your vehicle make model and year specify diagnostic programming required

                                                    

This keyless entry requires programming by your local dealer or locksmith. The procedure takes a few seconds to complete so many dealers will do it as a courtesy. If your dealer does charge a fee, local locksmiths usually charge much less.

 

You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment

1999 2000

99 00

All Models With Keyless Entry

O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

Olds Oldsmobile REGENCY

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

 

programming

1.   Insert key in ignition and leave in the OFF position

2.    Locate the Data Link Port. It is located under dash drivers side. Be sure you know
      which pins are 8 and 4.   

      (Note port is wider at top) Your OBDII port will not
           have numbers, use this diagram for reference. 

  

   

 


 




3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a 
        suitable jumper wire (leave the jumper wire connected throughout the programming
        procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond
        by locking and unlocking the doors to signify entering of programming mode.


4.    Close doors.

5.   Turn ignition to the ON position (as far as you can go without cranking the engine).
      Doors will lock. 

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to
       be programmed. After about 15 seconds, the vehicle will respond by locking and
       unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitters to be
       programmed.

8.    Remove jumper wire applied to th OBDII Port

1997 1998 1999

97 98 99

All Models With Keyless Entry

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

Olds Oldsmobile LSS

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

 

programming

1.   Insert key in ignition and leave in the OFF position

2.    Locate the Data Link Port. It is located under dash drivers side. Be sure you know
      which pins are 8 and 4.   

      (Note port is wider at top) Your OBDII port will not
           have numbers, use this diagram for reference.  



 
3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a 
        suitable jumper wire (leave the jumper wire connected throughout the programming
        procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond
        by locking and unlocking the doors to signify entering of programming mode.


4.    Close doors.

5.   Turn ignition to the ON position (as far as you can go without cranking the engine).
      Doors will lock. 

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to
       be programmed. After about 15 seconds, the vehicle will respond by locking and
       unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitters to be
       programmed.

8.    Remove jumper wire applied to th OBDII Port

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

“S” STANDARD EQUIPMENT RKE REMOTE KEYLESS  ENTRY : INSTALLED AT MANUFACTURE

Chevrolet Chevy Impala

Impala - must have factory radio in vehicle to perform on-board programming.

 

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

Impala - must have factory radio in vehicle to perform on-board programming.

 

(must specify programming)

( IMPALA must have factory working radio)

1.Turn the ignition to ACC or ON and the radio to off. Do not crank the engine.


2  Press and hold the DISP button on the radio for at least five seconds until settings is displayed.


3. Press the SEEK up or down arrows until FOB PROG appears on the display.

4 Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk next to it. BEGIN will be displayed.

5  Press the DISP button to start programming. When the message PUSH FOB flashes, press and
hold the LOCK and UNLOCK buttons on the first transmitter at the same time for 15 seconds. A chime will be heard to verify the transmitter is learned.

6.Repeat Step 5 for each additional transmitter up to four remotes total. You do not need to press DISP button again, just press down the LOCK and unLOCK buttons on the next transmitter to be learned to a maximum of four transmitters per vehicle.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

EXIT (Exit Feature Customization Mode): This feature allows you to exit the vehicle customization programming.
To Exit:
1. Scroll until EXIT appears on the display.
2. Press the DISP button to exit programming. A chime will he heard to verify the exit.

2000

00

Impala - must have factory radio in vehicle to perform on-board programming.

 

All Models With Keyless Entry

 

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

Impala - must have factory radio in vehicle to perform on-board programming.

Chevrolet Chevy MALIBU

 

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

1.    Close the vehicle doors.

2.   Turn ignition to the ON position then OFF.

3.   Remove key from the ignition.

4.   Press and hold the driver side door lock switch in the UNLOCK position
      until step 8.

5.   Insert the ignition key into the ignition lock cylinder and remove the key.
      (Do not turn the ignition key in the lock cylinder)

6.   Insert the ignition key into the ignition lock cylinder and remove the key.
      (Do not turn the ignition key in the lock cylinder)

7.   Insert the ignition key into the ignition lock cylinder.
      (Do not turn the ignition key in the lock cylinder)
      Leave key in the ignition cylinder.

8.   Release the door lock switch. The vehicle will sound three beeps in order
      to verify the Program Mode has been activated.

9.   Press the LOCK and UNLOCK buttons together on the keyless remote and
      hold unitl the vehicle beeps twice to verify that the keyless remote has been
      successfully programmed. This may take approximately 15 seconds.

10.  Perform the previous step (9) to program up to four keyless remotesm, including
       any old ones.

11.  Remove the ignition key to exit Program Mode

2000

00

All Models With Keyless Entry

 

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

Chevrolet Chevy MONTE CARLO

Monte Carlo and Impala - must have factory radio in vehicle to perform on-board programming.

1.       Turn the ignition to ACC or ON and the radio to off. Do not crank the engine.


2.       Press and hold the DISP button on the radio for at least five seconds until settings is displayed.


3.       Press the SEEK up or down arrows until FOB PROG appears on the display.

4.       Press the PREV or NEXT button to enter the submenu. The current selection will have an
        asterisk next to it. BEGIN will be displayed.

5.       Press the DISP button to start programming. When the message PUSH FOB flashes, press and
        hold the LOCK and UNLOCK buttons on the first transmitter at the same time for 15 seconds. A
        chime will be heard to verify the transmitter is learned.

6.    Repeat Step 5 for each additional transmitter up to four remotes total. You do not need to press
        the DISP button again, just press down the LOCK and UNLOCK buttons on the next transmitter
        to be learned to a maximum of four transmitters per vehicle.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

EXIT (Exit Feature Customization Mode): This feature allows you to exit the vehicle customization programming.
To Exit:
1. Scroll until EXIT appears on the display.
2. Press the DISP button to exit programming. A chime will he heard to verify the exit.

Monte Carlo and Impala - must have factory radio in vehicle to perform on-board programming.

 2000

00

All Models With Keyless Entry

 

“O” OPTIONAL RKE REMOTE KEYLESS  ENTRY : DEPENDS ON TRIM LEVEL OR OPTION PACKAGE INSTALLED AT DEALER

MAKE/MODEL

YEARS

Buick Park Avenue Ave Ultra

PROGRAMMING INSTRUCTIONS

1.      Insert keys in ignition and leave in the OFF position.

2.      Locate the OBDII  Port.

3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 and 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure).  Make sure you know which terminals are 8 and 4. The vehicle will respond by locking then unlocking the doors to signify entering of programming mode.

4.   Close Doors 

5.      Turn ignition to the ON position (as far as you can go without cranking the engine). Doors will lock.      

6.    Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. Up to about 30 seconds, the vehicle will respond by locking then unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitter (if any – including any existing remotes).

8.   Remove jumper wire applied to the OBDII Port

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

Buick LeSabre Le Sabre

PROGRAMMING INSTRUCTIONS

 

1.      Insert keys in ignition and leave in the OFF position.

2.      Locate the OBDII  Port.

3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 and 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure).  Make sure you know which terminals are 8 and 4. The vehicle will respond by locking then unlocking the doors to signify entering of programming mode.

4.   Close Doors 

5.      Turn ignition to the ON position (as far as you can go without cranking the engine).

      Doors will lock.      

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. Up to about 30 seconds, the vehicle will respond by locking then unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitter (if any – including any existing remotes).

2.       8.   Remove jumper wire applied to the OBDII Port

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

Buick Riviera

PROGRAMMING INSTRUCTIONS

1. Insert keys in ignition and leave in the OFF position.

2.      Locate the OBDII  Port.

3.      Make sure there are metal contact pins in terminals 8 and 4. Connect 8 and 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure).  Make sure you know which terminals are 8 and 4. The vehicle will respond by locking then unlocking the doors to signify entering of programming mode.

4.   Close Doors 

5.      Turn ignition to the ON position (as far as you can go without cranking the engine).

      Doors will lock.      

6.      Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. Up to about 30 seconds, the vehicle will respond by locking then unlocking the doors. Release the buttons on the transmitter.

7.      Within one minute, repeat the previous step on the remaining transmitter (if any – including any existing remotes).

8.   Remove jumper wire applied to the OBDII Port.

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

Pontiac Bonneville Boneville

SLE  SSEi

the manufacturer’s programming instructions For your vehicle make model and year specify diagnostic programming required

                                                    

This keyless entry requires programming by your local dealer or locksmith. The procedure takes a few seconds to complete so many dealers will do it as a courtesy. If your dealer does charge a fee, local locksmiths usually charge much less.

 

You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

Olds Oldsmobile Aurora

needs diagnostic programming from locksmith or local dealer

the manufacturer’s programming instructions For your vehicle make model and year specify diagnostic programming required

                                                    

This keyless entry requires programming by your local dealer or locksmith. The procedure takes a few seconds to complete so many dealers will do it as a courtesy. If your dealer does charge a fee, local locksmiths usually charge much less.

 

You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment

1996 1997 1998 1999

96 97 98 99

All Models With Keyless Entry

Chevrolet Chevy Impala

(must specify programming)

( IMPALA must have factory working radio)

1.Turn the ignition to ACC or ON and the radio to off. Do not crank the engine.


2  Press and hold the DISP button on the radio for at least five seconds until settings is displayed.


3. Press the SEEK up or down arrows until FOB PROG appears on the display.

4 Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk next to it. BEGIN will be displayed.

5  Press the DISP button to start programming. When the message PUSH FOB flashes, press and
hold the LOCK and UNLOCK buttons on the first transmitter at the same time for 15 seconds. A chime will be heard to verify the transmitter is learned.

6.Repeat Step 5 for each additional transmitter up to four remotes total. You do not need to press DISP button again, just press down the LOCK and unLOCK buttons on the next transmitter to be learned to a maximum of four transmitters per vehicle.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

EXIT (Exit Feature Customization Mode): This feature allows you to exit the vehicle customization programming.
To Exit:
1. Scroll until EXIT appears on the display.
2. Press the DISP button to exit programming. A chime will he heard to verify the exit.

2000

00

All Models With Keyless Entry

All of our keyless remotes are listed just as the manufacturer states for make model & year compatibility  -

 SOME VEHICLES HAVE KEYLESS SYSTEMS INSTALLED THAT HAVE STANDARD PACKAGES &

SOME ARE OPTIONAL (DEALER INSTALLED)

**(this can change what remote FCC ID &/or part will be compatible with your system)

** WE ASK THAT YOU VERIFY w/ A DEALER PRIOR TO PURCHASE AS TO WHAT FCC ID # YOU NEED FOR YOUR VIN

.

STOP!

 Before You Buy Please Read…

Program Remote To Your Vehicle

If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.

This remote needs to be programmed to your vehicle in order for it to work with your vehicle’s installed RKE (remote keyless entry ) system:

1.   Some years require diagnostic programming according to how the manufacturer set the system

         a.   Free programming Requirements per manufacturer upon request

         b.  Contact  us via  eBay messages (Keyless4u store) Prior to Purchase  

with  your vehicle’s ….

1.  Make

2.  Model

3.  Year

2.  We will respond via eBay messages with the manufacturer’s programming requirements so that you can determine if you are capable of programming your vehicle or if you will need to visit a local dealer or locksmith for programming with a diagnostic scan tool – we do not write the programming – we pass it on to you as a courtesy.

How to find out if this remote is compatible with your Vehicles’ installed RKE System

If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.

1.   Check the back of your current or old keyless remote to match FCC ID /Part #’s.

2.   Contact your local dealer and tell them your VIN# and ask what part # / FCC ID you need.

Your vehicle will be installed with one of the following keyless entry systems:  

  a. Standard Keyless Remote Packages: Installed at time of manufacture. 

  b. Optional Keyless Remote Packages: Installed by a dealer. 

  c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. 

  d. No remote keyless entry system at all.

The above information can change which remote you need
for your installed remote keyless system.

 

Australian Customers: The frequency of our remotes typically do not match the frequency needed for Australian Model Remotes. Please verify that this remote will work for your vehicle prior to purchase.

 

Payment:  We accept payment via PayPal or Credit Card. Please contact us via eBay messages for any questions concerning payments.  Payment is expected within 5 days

PA SALES TAX:  As per the State of PA Franchise Board we must collect sales tax from PA Residents for any purchase made from our store.

Contact/Email: Due to scams etc, we DO NOT respond to emails. We only read/respond to EBAY MESSAGES. Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. Please contact us with questions via eBay messages (keyless4u).

 

100% Guarantee Remote Shipping / Return Policy

Shipping & Handling

Combined Shipping & Handling Discount (multiple item purchase discount):

S&H discount = the price of the 1ST remote’s S&H  + 1.99 each additional remote’s  S&H 

Shipped From: Pennsylvania, USA

Shipping Method: USPS mail service

USA Shipment Options:

   ◊ USPS 1ST class mail service

   ◊ USPS Priority class mail service

   ◊ USPS EXPRESS class mail service

Canadian Shipment Options:

   ◊ USPS 1ST class mail service

   ◊ USPS Priority class mail service

   ◊ USPS Express class mail service

Worldwide (Outside of  USA & Canada) Shipment Options:

   ◊ USPS Priority class mail service

   ◊ USPS Express class mail service

Australian Customers: The frequency of our remotes typically do not match the frequency needed for Australian Model Remotes. Please verify that this remote will work for your vehicle prior to purchase.

 

Warranty/Returns:  

1.     We have a 30 day return policy. 

2.     All returns for replacements and refund need an RMA #.

3.     Please contact us before returning items so we can give you the RMA # and the proper return address.

4.     No refunds / replacements will be granted without an RMA#

 

We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged.

Please Note: Each remote and circuit board is UV id’d prior to shipment  – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement.

 

  Does this keyless remote entry come with a battery?  

Yes. It will have a working battery installed.

Battery Condition:

        A. All remotes sold on Keyless4u include working batteries.

        B. Installed batteries are not tested for battery life- they are simply working.

             Some are new and some are used.

 


WORD KEY:

 
Thank You! If you have questions send us an eBay message.