BEFORE YOU BUY PLEASE READ … This item is pre-owned – it will work like new once programmed to your vehicle
One (1)
O.E.M. Original Equipment Manufacturer Factory
remote keyless entry fob alarm
Transmitter control clicker keyfob controller replacement
Functions at 100% Tested & Guaranteed
| Item #: |
PRE-OWNED 8c, 8d |
|---|---|
| FCC ID: | ABO1502T, AB01502T |
| Part #: | 16245100-29, 16245103, 16207901-5 (16245100, 16207901, 162079015, 1624510029) |
| Canada/Mexico Part #: | 218101368 |
WORKING BATTERY INSTALLED
BEFORE YOU BUY PLEASE READ …
Remote / Battery Specifications
Condition: PRE-OWNED Battery: Yes, Installed Buttons: 3: Lock, Unlock,Trunk Required Batteries:
Frequency: 315MHz (315 MHz) Compatible Vehicles*:
1997 1998 1999 Chevy Cavalier
1997 1998 1999 2000 2001 Chevy Lumina
1997 1998 1999 Chevy Malibu
1997 1998 1999 Chevy Monte Carlo
1997 Oldsmobile Cutlass Supreme
1997 1998 1999 Oldsmobile Cutlass
1997 1998 Pontiac Gran Am
1997 1998 1999 Pontiac Sunfire GT
*All vehicles with factory installed Remote Keyless Entry (RKE)
All of our keyless remotes are listed just as the manufacturer states for make model & year compatibility
SOME VEHICLES HAVE KEYLESS SYSTEMS INSTALLED THAT HAVE STANDARD PACKAGES & SOME ARE OPTIONAL (DEALER INSTALLED)
This can change what remote FCC ID &/or part will be compatible with your system
WE ASK THAT YOU VERIFY w/ A DEALER PRIOR TO PURCHASE AS TO WHAT FCC ID # YOU NEED FOR YOUR VIN
|
MAKE/MODEL |
YEARS |
|
Pontiac Grand Am PROGRAMMING 1. Make sure ignition is in the OFF position. 2. Locate the programming connector in the trunk (drivers side). It is a plastic connector with two wires leading up to it. The connector is not plugged into anything. You may have to pull back trim to access connector. 3. The programming connector should have two terminals.
Connect both terminals with a suitable jumper wire. Make sure the terminals
remain connected throughout the programming procedure. 5. Repeat the previous step for each additional remotes (including any existing remotes) Do not remove jumper wire in between programming of remotes. 6. Remove the jumper wire from the Keyless Remote Connector. |
1997 1998 97 98 All Models With Keyless Entry |
|
CHEVY CHEVROLET CAVALIER Z24 Z 24 1. Make sure ignition is in the OFF position. 2. Locate the Programming Connector in the trunk (driver’s side). It is a plastic connector with two wires leading up to it. The connector is not plugged into anything. You may have to pull back trim to access the connector. 3 The programming connector should have two terminals. Connect both terminals with a suitable jumper wire. Make sure the terminals remain connected throughout the programming procedure. 4. Press the LOCK and UNLOCK buttons on the transmitter simultaneously. In response, the Keyless Entry Module will cycle all the Door Lock Motors at once. Your new remote has been accepted and all existing remote codes have been erased. 5. Repeat the previous step for each additional transmitter (including any existing transmitters). Do not remove jumper wire in between programming of transmitters. 6. Remove the jumper wire from the Keyless Programming Connector. |
1997 1998 1999 97 98 99 All Models With Keyless Entry |
|
CHEVY CHEVROLET MONTE CARLO 1. Locate the Programming Connector leading to the receiver in the trunk (passenger side). It is a plastic connector with one wire leading up to it. The connector is not plugged into anything. You may have to pull back the right side trunk trim to access the connector. 2.
The programming connector should have one terminal. Ground this terminal to
the trunk hatch or 3. Press and hold the LOCK and UNLOCK buttons on the transmitter for 12 seconds or until the door locks will cycle once. Your new remote has been accepted and all existing remote codes have been erased. 4. Repeat the previous step for each of the remaining transmitters (including any existing transmitters). Do not remove ground between programming of transmitters. 5. Remove the jumper wire from the keyless programming connector. |
1997 1998 1999 97 98 99 All Models With Keyless Entry |
|
CHEVY CHEVROLET LUMINA Z34 Z 34 Note: Existing keyless remotes will be erased with this procedure. Existing working remotes will have to reprogrammed also. 1. Locate the programming connector wire located
in the RH trunk area. You may have to pull back right side trunk
trim on trunk wall to locate
the single black/white wire. 3. System will now lock and unlock doors
automatically to indicate 4. Press and hold the LOCK and UNLOCK buttons
on keyless remote at the same
time for 15 seconds or until the door locks lock and unlock
once. This indicates that your new keyless remote has been programmed
and 5. Repeat step 4 for to program any additonal keyless remotes including and existing keyless remotes. Do not remove ground wire between programming of keyless remotes. 6. Disconnect programming connector wire from ground to exit programming mode. 7. Test keyless remote(s). |
1997 1998 1999 2000 2001 97 98 99 00 01 All Models With Keyless Entry |
|
CHEVY CHEVROLET MALIBU 1. Make sure ignition is in the OFF position. 2. Locate the Programming Connector in
the trunk (center of rear shelf). It is a plastic connector with 3. The programming connector should have
two terminals. Connect both terminals with a suitable 4. Press and hold the LOCK and UNLOCK
buttons on the transmitter simultaneously for at least 15 5. Repeat the previous step for each
transmitter to be programmed. Do not remove jumper wire in 6. Remove the jumper wire from the Keyless Programming Connector |
1997 1998 1999 97 98 99 All Models With Keyless Entry |
|
OLDS OLDSMOBILE CUTLASS NEW BODY STYLE 1. Make sure ignition is in the OFF position. 2.
Locate the Programming Connector in the trunk (center of rear shelf). It is a
plastic connector with 3.
The programming connector should have two terminals. Connect both terminals
with a suitable 4.
Press and hold the LOCK and UNLOCK buttons on the transmitter simultaneously
for at least 15 5. Repeat the previous step for each transmitter to be programmed. Do not remove jumper wire in between programming of transmitters. 6. Remove the jumper wire from the Keyless Programming Connector. |
1997 1998 1999 97 98 99 All Models With Keyless Entry |
|
OLDS OLDSMOBILE CUTLASS SUPREME Note: Existing keyless remotes will be erased with this procedure. Existing working remotes will have to reprogrammed also. 1. Locate the programming connector wire located in the RH trunk area. You may have to pull back right side
trunk trim on trunk wall to locate the single black/white wire. 3. System will now lock and unlock doors automatically to indicate programming mode has been activated. 4. Press any button on keyless remote. System will respond by locking and unlocking doors one time to indicate successful programming. 5. Repeat step 4 for to program any additonal keyless remotes including and existing keyless remotes. Do not remove ground wire between programming of keyless remotes. 6. Disconnect programming connector wire from ground to exit programming mode. 7. Test keyless remote(s).
|
1997 97 All Models With Keyless Entry
|
|
PONTIAC SUNFIRE GT 1. Make sure ignition is in the OFF position. 2. Locate the programming connector in the trunk
(drivers side). It is a plastic connector 3. The programming connector should have two
terminals. Connect both terminals with a 4. Press the LOCK and UNLOCK buttons on the remote
at the same time. In response, the 5. Repeat step 4 now for each additional remotes,
including any exiting remotes. DO NOT 6. Remove jumper wire and test remotes. |
1997 1998 1999 97 98 99 All Models With Keyless Entry |
All of our keyless remotes are listed just as the manufacturer states for make model & year compatibility -
**SOME VEHICLES HAVE KEYLESS SYSTEMS INSTALLED THAT HAVE STANDARD PACKAGES & SOME ARE OPTIONAL (DEALER INSTALLED)
**(this can change what remote FCC ID &/or part will be compatible with your system)
** WE ASK THAT YOU VERIFY w/ A DEALER PRIOR TO PURCHASE AS TO WHAT FCC ID # YOU NEED FOR YOUR VIN
STOP!
Before You Buy Please Read…
Program Remote To Your Vehicle
If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.
This remote needs to be programmed to your vehicle in order for it to work with your vehicle’s installed RKE (remote keyless entry ) system:
1. Some years require diagnostic programming according to how the manufacturer set the system
a. Free programming Requirements per manufacturer upon request
b. Contact us via eBay messages (Keyless4u store) Prior to Purchase
with your vehicle’s ….
1. Make
2. Model
3. Year
2. We will respond via eBay messages with the manufacturer’s programming requirements so that you can determine if you are capable of programming your vehicle or if you will need to visit a local dealer or locksmith for programming with a diagnostic scan tool – we do not write the programming – we pass it on to you as a courtesy.
How to find out if this remote is compatible with your Vehicles’ installed RKE System
If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first.
1. Check the back of your current or old keyless remote to match FCC ID /Part #’s.
2. Contact your local dealer and tell them your VIN# and ask what part # / FCC ID you need.
Your vehicle will be installed with one of the following keyless entry systems:
a. Standard Keyless Remote Packages: Installed at time of manufacture.
b. Optional Keyless Remote Packages: Installed by a dealer.
c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop.
d. No remote keyless entry system at all.
The above
information can change which remote you need
for your installed remote keyless system.
Australian Customers: The frequency of our remotes typically do not match the frequency needed for Australian Model Remotes. Please verify that this remote will work for your vehicle prior to purchase.
Payment: We accept payment via PayPal or Credit Card. Please contact us via eBay messages for any questions concerning payments. Payment is expected within 5 days
PA SALES TAX: As per the State of PA Franchise Board we must collect sales tax from PA Residents for any purchase made from our store.
Contact/Email: Due to scams etc, we DO NOT respond to emails. We only read/respond to EBAY MESSAGES. Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. Please contact us with questions via eBay messages (keyless4u).
100% Guarantee Remote Shipping / Return Policy
Shipping & Handling
Combined Shipping & Handling Discount (multiple item purchase discount):
S&H discount = the price of the 1ST remote’s S&H + 1.99 each additional remote’s S&H
Shipped From: Pennsylvania, USA
Shipping Method: USPS mail service
USA Shipment Options:
◊ USPS 1ST class mail service
◊ USPS Priority class mail service
◊ USPS EXPRESS class mail service
Canadian Shipment Options:
◊ USPS 1ST class mail service
◊ USPS Priority class mail service
◊ USPS Express class mail service
Worldwide (Outside of USA & Canada) Shipment Options:
◊ USPS Priority class mail service
◊ USPS Express class mail service
Australian Customers: The frequency of our remotes typically do not match the frequency needed for Australian Model Remotes. Please verify that this remote will work for your vehicle prior to purchase.
Warranty/Returns:
1. We have a 30 day return policy.
2. All returns for replacements and refund need an RMA #.
3. Please contact us before returning items so we can give you the RMA # and the proper return address.
4. No refunds / replacements will be granted without an RMA#
5. All cut keys are subject to a $20 deduction from the refund
We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged.
Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement.
Does this keyless remote entry come with a battery?
Yes. It will have a working battery installed.
Battery Condition:
A. All remotes sold on Keyless4u include working batteries.
B. Installed batteries are not tested for battery life- they are simply working.
Some are new and some are used.
WORD KEY: