PAINTED AUDI A4 FACTORY STYLE SPOILER 2002-2007

Brand New Factory Style Spoiler for 2002-2007 Audi A4.  This spoiler comes painted to match your car.  Spoiler is painted with Dupont factory matched OEM paint and comes with a 3 year warranty.  Please select your paint code from below and note the paint code when ordering.  Please email any questions.  See picture for more details.

COLORS WE HAVE IN STOCK:

Q1 : Liquid Blue

LY7G/Q4 : Quartz Gray

LY1Q/9X : Dakar Beige

LY3J/C8 :  Brilliant Red

LY9B/A2 :  Brilliant Black

LY3C : Amulet Red 

LY7W- Lt Silver Metallic

Made from Blow-Molded ABS

Lightweight and won't crack like fiberglass

Mounting hardware, installation instructions, and template included.

We can ship to Alaska, Hawaii, Canada, and Puerto Rico. Please choose International Shipping Charges of $50.00

Bolt-On Application STEP-by-STEP

STEP 1.
After opening and inspecting your  rear spoiler you can begin the installation. Notice that the LED light and the pedestal gaskets come pre-installed from the factory (pre-painted spoilers only), which will shave some time off the installation.

STEP 2.
Start out by turning over the spoiler and setting it on a soft surface, to prevent any scratches. Place the plastic locator T-strips into the mounting holes on spoiler and LED brake light hole. TIP: A small piece of masking tape is helpful in holding the T-strips in position.

STEP 3.
Place spoiler on closed decklid and align to proper position. A measuring tape will ensure a "perfect" alignment.

STEP 4.
Using masking tape, secure locator T-strips to the decklid of the vehicle. Simply remove the spoiler by lifting straight up leaving the T-strips secured to the decklid.

STEP 5.
Using a 1/8" drill bit, drill thru the T-strip holes and into the decklid. It is not necessary to drill through a double panel on this particular application because we can utilize the factory openings on the underside.

STEP 6.
Remove T-strips and using a 5/16" drill bit, drill thru the 1/8" hole in step 5. If a "double panel" does exist, use a 3/4" drill bit to drill thru the "inner panel". This allows the ratchet or nutdriver to secure the screw tightly against the upper panel.

STEP 7.
After deburring all holes, apply small amounts of primer which will help prevent rusting of the freshly drilled metal.

STEP 8.
Pull back pedestal gaskets exposing mounting tape and place spoiler on decklid and using supplied screws secure to the vehicle using a ratchet or nutdriver. Be sure to feed the LED light wire through the pre-determined hole. Apply small amounts of silicone based caulk over mounting screws as this will help prevent leaking, rusting, or loosening of screws. TIP: Gasket material is extremely sticky once exposed, so we found that spraying it with water or glass cleaner will allow you to reposition spoiler as needed.

STEP 9.
When installing a LED brake light it is recommended to splice into the 3rd brake light in the vehicle and attach spoiler wires using electrical tape. Step on the brake light to ensure proper wiring, simply switch the two connections if spoiler does not light.

STEP 10.
Finish your install by vacuuming any debris or metal shavings and then reinstall any panels, mats or other items that may have removed earlier in installation.

No Drill Application STEP-by-STEP

Step 1. Surface Cleaning
Clean surface area that is to be covered by spoiler thoroughly, with Isopropyl Alcohol.

Step 2. Test Fitting the Unit
Before removing the tape backing, test fit spoiler in order to get comfortable with the placement. You can mark the position with a grease pen or masking tape for a perfect fit.

Step 3. Preparation
Peel back the corner of the red liner on the 3M tape and remove all pieces, avoid touching exposed tape.

Step 4. Installation
Gently press spoiler into place on the deck lid, hatch or rear glass. Once satisfied with placement, firmly press down on spoiler to ensure cohesion along entire vehicle surface. Continue to apply pressure or use masking tape to keep unit from lifting.

Helpful Tips
Adhesive silicone and/or adhesion promoters are often used in conjunction with provided 3M tape for long lasting durability. For best results installation should be conducted in temperatures above 72. Refer to tape manufacturers recommendations for full details. Do Not clean, wash, wax or drive for 12 hours after installation. Shopitall is not responsible for no drill attachment durability.