Buy for the future brake job!!!

This is a 3/16 inch metal brake line replacement kit. All lines are supplied double-flared at each end with S.A.E. specified male inverted flare fittings attached and are ready for quick and easy installation. All brake lines have an extra long nut on one end to seat in late model deep-seated wheel cylinders. These maliable lines are easy to bend or coil without collapsing the tubing or restricting the flow of brake fluid. Six couplers are included to join lines where necessary. Instructions are also included.



this kit is for the following:

Chryslers:
Cordoba 1975 to 1983
Fifth Avenue 1983 to 1986
Imperial 1960 to 1975
LeBaron 1977 to 1989
Newport 1960 to 1981
New Yorker, Town & Country 1960 to 1989
Chrysler 300 1963 to 1968

Dodge:
Aspen 1977 to 1980
Challenger 1970 to 1983
Conquest 1984 to 1987
Coronet 1965 to 1976
Dart 1961 to 1976
Demon 1971 to 1976
Dipolmat 1977 to 1989
Lancer 1961 to 62
Mirada, Magnum 1979 to 1981
Monaco, Polara 1960 to 1978
Omni, 024, Charger, Shelby Charger 1966 to 1982
St. Regis 1979 to 1981
Super Bee 1968 to 1971
Swinger 1967 to 1976
400 Special LS 1982 to 1983
880 1963 to 1966

Plymouth:
Barracuda 1964 to 1974
Belvedere 1962 to 1970
Duster, Scamp Valiant 1960 to 1976
Fury, Road Runner, Satellite, Sebring, GTX, 1965 to 1989
Horizon , TC3, Turismo 1978 to 1982
Sundance 1988 to 1990
Volare 1976 to 1980

Here is a list of what lines are included to do your car:

6 inch

8 inch (Qty. 2)

12 inch (Qty. 2)

14 inch

17 inch

20 inch (Qty. 2)

23 inch

27 inch

30 inch (Qty. 2)

33 inch

37 inch

40 inch

44 inch

48 inch

51 inch (Qty. 3)

six unions to join lines together

instructions for installation

A total of 27 lines and unions!!

 

This kit contains all the lines to do a wide variety of cars, and many different configurations, so you will have unused lines in any installation. These extra lines are a bonus that can be used for other projects

The tubing is double walled, seamless and copper fused with a special inner and outer coating to provide protection from abrasion and corrosion. This is the same tubing that is used on new cars!

All cars from 1967 and up use a dual braking systems. You may need re-use or obtain an adapter to attach the line to the master cylinder and to the brake block.

All information on lines are for OEM brake systems only. However, this kit has many lengths and will service most modified system except any system with "larger" 1/4 (.25 inch OD) lines.

All lines are slighly longer than OEM to allow for "lazy" DIY bends.

If you need a very sharp bend next to the flare at the end of the line, you will need a bender listed under "tools/supplies" on our Ebay store.

All unions are solid brass to stop rust.

All lines are made in USA or Canada and are 3/16" outer diameter with a factory flare.

A very few Mopars use a large 3/8" line to the front brake block, which is not supplied.

Fits the years: 1960 61 1961 62 1962 63 1963 64 1964 65 1965 66 1966 67 1967 68 1968 69 1969 70 1970 71 1971 72 1972 73 1973 74 1974 75 1975 76 1976 77 1977 78 1978 79 1979 80 1980 81 1981 82 1982 83 1983 84 1984 85 1985 86 1986 87 1987 88 1988 89 1989

4715