FCC ID: GOH-FOUR

 (Alternate Spelling: GOHFOUR G0H-FOUR G0H-FOUR)

 Part #: PT-4

 Frequency: 433.5 MHz

LED color: none

4 buttons

Compatible with the following systems:

 P-5500, E-6500, CSM-2-5-3

also work some functions on:

P-100, P-750, P-1000,

P-3500, P-350, C-400,

C-450, C-500, C-550

E-1100, E-COM, E-950,

E-1500, E-2000, E-4500,

RKE-1, RCS-2

Programming Instructions:

Adding Remote Transmitters to Your System

Your security system has the ability to operate from up to four (4) remote transmitters. Follow these instructions to add a remote transmitter to your system.

1.   Make sure the security system is disarmed and the ignition is off.

2.   Without starting the vehicle, turn the ignition ON, OFF, then ON, at 1/2-second intervals.

After two (2) seconds, the status indicator will begin flashing for Code Entry. Follow the Code Entry Procedure. If the correct code is entered, the siren will chirp twice, indicating entry into the Transmitter Programming Mode.

3.   Wait 5 seconds. Press the ARM button on the remote transmitter to be programmed. The siren will chirp once, indicating that the system has "learned" that transmitter.

4.   Repeat step 3 for any additional remote transmitters.

5.   Exit the Transmitter Programming Mode by turning the vehicle ignition on, then off. Test all remote transmitters to ensure that they work properly.

Deleting Lost or Stolen Remote Transmitters from Your System

If one of your remote transmitters is lost or stolen, follow these instructions IMMEDIATELY to remove the transmitter code from your system.

1.   Make sure that you have all remaining remote transmitters available.

2.   Enter the transmitter programming mode by following steps 1 and 2 under Adding Remote Transmitters to Your System (above).

3.    

a.   If you have only one remaining remote transmitter, press the ARM button on that remote transmitter four (4) times, pausing at least five seconds in between each press. Make sure that the siren chirps each time you press the ARM button.

b.   If you have two remaining remote transmitters, press the ARM button on each remote transmitter two (2) times, pausing at least five seconds in between each press. Make sure that the siren chirps each time you press the ARM button.

c.   If you have three remaining remote transmitters, press the ARM button on the first remote transmitter two (2) times, then press the ARM button on the other two remote transmitters once. Pause at least five seconds in between each press. Make sure that the siren chirps each time you press the ARM button.

4.   When you are finished, the lost or stolen remote transmitter will no longer operate your system.

Programming Selectable Options

1.   Make sure the system is disarmed and the ignition is off

2.   Without starting the vehicle turn the ignition ON, OFF, ON, OFF, then ON, at 1/2-second intervals

After two (2) seconds the status indicator will begin flashing for Code Entry. Follow the Code Entry Procedure. If the correct code is entered the siren will chirp three times, indicating entry into the Selectable Options Mode.

3.   Press the ARM button on a programmed transmitter to begin option selections.

Code Entry Procedure

This security system utilizes a secret code for adding or deleting remote transmitters, changing system options and disarming the alarm if the remote transmitter fails to operate. The 4 digit code should be written on the front of this manual by your installer If not the code is found on a sticker on the back of the alarm module Below is the procedure for entering the code.

1.   Enter the Code Entry Mode by following the steps in the Adding Remote Transmitters to Your System, Programming Selectable Options or the Emergency Disarm Procedure sections of this manual

The status indicator will begin flashing for Code Entry

2.   Look at the first number in the code Allow the status indicator to flash the corresponding number of times as the first number in the code

3.   After the status indicator has flashed the corresponding number of times, turn the vehicle ignition off The first number has been entered

4.   Turn the ignition back to the ON position The status indicator will again begin flashing Repeat the procedure in steps 2 and 3 this time using the second number in the code

5.   Repeat steps 2 and 3 for the third and fourth numbers in the code

6.   After the fourth number has been entered correctly the alarm will disarm, or enter the desired programming mode

Note: If you enter an incorrect digit turn the vehicle ignition off then on. When the status indicator begins to flash, re-enter the code from the beginning

Example: The code is 2314

1.   Enter the Code Entry mode The status indicator will begin flashing for Code Entry

2.   Allow the status indicator to flash two (2) times After the second flash turn the vehicle ignition off

3.   Wait one second then turn the ignition on

4.   Allow the status indicator to flash three (3) times After the third flash turn the vehicle ignition off

5.   Wait one second then turn the ignition on

6.   Allow the status indicator to flash one (1) time After the flash turn the vehicle ignition off

7.   Wait one second then turn the ignition on

8.   Allow the status indicator to flash four (4) times After the fourth flash turn the vehicle ignition off

IMPORTANT!!!

Be sure to remember your code and keep it in a safe place. If the code is lost, it cannot be recovered.

Instructions for programming your new Code Alarm Remote (2 & 4 Button Transmitters Only)

Note: Each System module has four “slots”, or memory locations, to store transmitter codes, giving it the ability to operate from up to four transmitters.

For proper operation, a transmitter code must be stored into each memory slot.

When using less than four transmitters, follow the suggested programming parameters:

· One Remote Transmitter – Program four (4) times

· Two Remote Transmitters – Program each transmitter two (2) times.

· Three Remote Transmitters – Program two transmitters one (1) time, and the remaining transmitter twice.

1. Open the driver’s door, leave the door open and make sure the dome light is ON.

2. Turn vehicles ignition on (Ignition ON engine OFF).

3. Press and hold emergency override button (A small black headed push button commonly found under the driver side dash) After about 10-13 seconds, the siren or horn will sound three (3) times. This indicates that the unit has entered the transmitter-programming mode.

4. Continue to hold in the programming override button.

5. Press the ARM (or LOCK) button on the remote transmitter to be programmed. The siren or horn will sound once, indicating that the

system has “learned” that remote transmitters code.

6. Repeat step 5 for any additional transmitters or transmitter codes.

7. Release the programming override button.

8. Turn the ignition off to exit the programming mode. Test remote transmitters to ensure that they work properly by toggling back & forth

the LOCK and UNLOCK buttons.