Chevrolet, Gm, Gmc Truck 15530202 Hyd Clutch Bellhousing, Bell Housing on 2040-parts.com
Fallbrook, California, United States
|
Here we have a Heavy Duty Chevy hydraulic
setup bellhousing for either a New Process 883 or SM465. The actual
casting numbers are: 15530202. This one is large enough to handle the
Chevy large 168 tooth 14 inch flywheel and 12 inch clutch. It fits all
the older small and big block Chevy engines from 283-454, and has the 5
and 1/8 inch center hole. This bell has been cleaned and blasted to
clear it of all dirt and debris. It has also been checked and verified
true all over for proper mounting to the engine, and for proper mounting
of the tranny to it, plus clearance for the clutch and flywheel, plenty
of room (16 inches from top to bottom inside clearance). All the bolt holes are in great
condition. The Clutch pivot ball is brand new. The shipping rate is a
flat rate of $30.00 in the lower 48 U.S. states only. In addition, RURAL
ROUTE type addresses, where a surcharge is tacked on, will have an
additional charge applied to the invoice. Package will be sent to you
via UPS Ground with a tracking number. I will ship elsewhere on a case
by case basis but, email me first to inquire, so that I can check your
shipping options and rates to see if it will be feasible for the both of
us. I will not lose money on shipping. NOTE: I also
sell 621's, 697's, 486's, 15530202's, 383's, 421's, 403's, 6283756's,
and both new or used forks, rubber boots and inspection shield covers to
match them, for a small additional price. They may not all be in my
auction right now, but email me and I'll send pictures of what I have.
Some have been repaired yet guaranteed to work great. Some are in
original condition and ready to install. All are immaculate and go for
some of the best prices you'll find. Check out my other auctions and
email me with any questions, we can make a deal.
|
Manual Transmission Parts for Sale
Chevrolet, gm, gmc truck 486 hd bellhousing, bell housing(US $150.00)
Chevrolet chevy gm gmc 409 performance bellhousing bell housing(US $500.00)
1994-04 mustang t-5 input shaft and bearing retainer(US $39.95)
Ford a-7141 reverse idler gear 17 teeth helical(US $29.25)
Corvette original transmission mount bracket 1963-1967(US $50.00)
T5 world class manual trans. bearing retainer aluminum base fits '83-'93 ford(US $57.95)
Audi Q3: Official
Wed, 13 Apr 2011Audi Q3 – finally official Ahead of its official reveal at Shanghai this month, the baby SUV that is the Audi Q3 has bowed in, with plenty of detail and lots of photos. Looking exactly how it was expected to look – pretty much the same as the 2007 Audi Cross Coupe Concept , without the Concepty bits – and ready to fit in under the Q5 and mop up sales from those who want a premium, compact softroader. Under the skin the Audi Q3 is pure VW Tiguan, but Audi has grafted on a convincing set of sheet metal – and a typical, classy Audi interior – to put proper daylight between the cousins.
BMW Toyota diesel engine deal not for Lexus
Sun, 18 Dec 2011Lexus won't get BMW diesel engines despite the Toyota deal The deal for BMW to supply Toyota with diesel engines for its range in Europe will not extend to Lexus models. The deal for BMW to supply diesel engines to Toyota for Europe (and joint work on advanced lithium ion battery technology) makes a lot of sense. BMW’s diesel engine are possibly the best there are, and Toyota need good diesel offerings in Europe to mop up sales.
New Honda CR-V arrives – again
Wed, 18 Jul 2012The 2013 Honda CR-V has been revealed ahead of a launch in to the UK market in October after a Paris Motor Show debut. Regular readers may realise that this isn’t the first time we’ve announced the arrival of the new Honda CR-V. Back in March we revealed the new Honda CR-V was on the way to the Genev Motor Show before launching in the UK in September.