Chevrolet, Gm, Gmc Truck 486 Hd Bellhousing, Bell Housing on 2040-parts.com
Fallbrook, California, United States
|
Heavy Duty Chevy 486 bellhousing. This one
will accept the SM465. The actual casting numbers are: 460486. This one
is large enough to handle the Chevy large 168 tooth 14 inch flywheel and
12 inch clutch. It fits all the older small and big block Chevy engines
from 283-454, and has the 5 and 1/8 inch center hole. This bell has
been cleaned and blasted to clear it of all dirt and debris. It has also
been checked and verified true all over for proper mounting to the
engine, and for proper mounting of the tranny to it, plus clearance for
the clutch and flywheel, plenty of room (16 inches from top to bottom
inside clearance). All the bolt holes are in great condition. The
Clutch pivot ball has been removed, cleaned and threads checked, they
are good to go. The shipping rate is a flat rate of $30.00 in the lower
48 U.S. states only. In addition, RURAL ROUTE type addresses, where a
surcharge is tacked on, will have an additional charge applied to the
invoice. Package will be sent to you via UPS Ground with a tracking
number. I will ship elsewhere on a case by case basis but, email me
first to inquire, so that I can check your shipping options and rates to
see if it will be feasible for the both of us. I will not lose money on
shipping. NOTE: I also sell 621's, 697's, 486's,
15530202's, 383's, 421's, 403's, 6283756's, and both new or used forks,
rubber boots and inspection shield covers to match them, for a small
additional price. They may not all be in my auction right now, but email
me and I'll send pictures of what I have. Some have been repaired yet
guaranteed to work great. Some are in original condition and ready to
install. All are immaculate and go for some of the best prices you'll
find. Check out my other auctions and email me with any questions, we
can make a deal.
|
Manual Transmission Parts for Sale
Chevrolet chevy gm gmc 409 performance bellhousing bell housing(US $500.00)
1994-04 mustang t-5 input shaft and bearing retainer(US $39.95)
Ford a-7141 reverse idler gear 17 teeth helical(US $29.25)
Corvette original transmission mount bracket 1963-1967(US $50.00)
T5 world class manual trans. bearing retainer aluminum base fits '83-'93 ford(US $57.95)
1970 1971 jeep/amc cj 5 6 t 14 15 bell housing v8 6 cylinder 258 304 bellhousing(US $150.00)
Lamborgini Jota (or nota Jota) Tease 4
Mon, 20 Sep 2010Lamborghini Jota Tease 4 So here we go with what is either tease three of Lamborghini’s slow unwrapping of its Paris surprise, or tease four if you count the Lamborghini Jota bonnet tease from back in June. So what do we get this time round? Well, we think it’s a bit of the interior.
Holden shows Efijy concept at the Australian International Motor Show
Wed, 02 Nov 2005Holden's designers and engineers have delivered a knockout showcar at last month's Australian International Motor Show in Sydney. The Efijy (effigy - n. a stylistic representation of someone or something famous) is a stunning nod to the classic 50s FJ Holden with steroid-fed hot rod lines.
Ford Ranger gets rollover control for 2010
Fri, 06 Feb 2009The Ford Ranger pickup will roll into the 2010 model year this summer equipped with the automaker's stability-control system that includes a rollover sensor. The rollover sensor measures the truck's angle of tilt and engages the antilock braking system to help prevent a rollover. Ford uses the technology, which it calls AdvanceTrac with RSC, throughout its vehicle lineup.