Energy Del Sol Adh-pm68 Kit Solar Panel Energy Flex Power Mat Kit on 2040-parts.com
Charlotte, North Carolina, US
Energy Del Sol ADH-PM68 KIT Solar Panel Energy Flex Power Mat Kit
Kit Includes 12V 30 Amp Digital Charge Controller along with 25' of 10 Gauge Wire.
Top 4 Reasons why the FLEX POWER MAT™ beats crystalline panels hands down:
1) Unmatched in Durability – In Fact, You Can Even Walk On It!
Our panel can withstand hail storms and other weather including extreme heat and cold. (Most hard panels will melt the crystal in extreme heat.) In fact if you were to damage any section of the panel it will only affect that panel in our mat. Crystalline panels cannot be walked on thus restricting your roof access and also will crack and break in some extreme weather including hail storms.
2) Greater Efficiency – Draws Power for Longer Periods Throughout the Day
The Flex Power Mat is composed of 3rd generation, triple junction amorphous silicone, which means that our panel gathers all three rays of light. This allows it to draw power from the sun at lower angles and for longer periods throughout the day.
The Flex Power Mat generates 68Watts, 4.1AMP’s and 16.5Volts but is capable of producing more energy over the course of a day than crystalline panels with higher wattage due to flush mounting the crystalline panel on the roof of your RV. Crystalline panels can lose up to approximately 40% of their energy production capability by not having them angled to the sun. As we know, most people leave have their panels mounted flush on the roof and do not angle or tilt them to the sun throughout the day.
3) The Flex Power Mat Even Draws Power In the Shade!
The Flex Power Mat has Bypass Diodes and is Shadow Tolerant, which means that it has more efficient energy production even on overcast/dull days. Most crystalline panels when shadowed even 25% will not be producing power. Our panel produces power even when shaded by trees. So feel free to park at your favorite location and not have to worry about your panel producing power.
4) Ultra Low-Profile, Aerodynamic Design
The Flex Power Mat creates no wind chatter when traveling and its low-profile, aerodynamic design is perfect for resistance in high winds. This low-profile design also means that it is aesthetically pleasing on your roof, unlike bulky, non-aerodynamic crystalline panels. Our panel also creates no wind drag or wind load when traveling. With the Flex Power Mat, you never have to worry about climbing up and down on your roof to adjust or lock down your panel before or after traveling.
In addition to the Top 4 reasons already listed, below are even more reasons why you should choose the Flex Power Mat for your RV, boat or other mobile solar power needs:
• The Flex Power Mat is capable of conforming to just about any rooftop surface and design. Our durable EPDM rubber mounting system with micro sealant adhesive is designed specifically for the roof tops of recreational vehicles and also creates a gasket on your roof so there is no need for silicones and sealants when installing the Mat.
• 25 year warranty on power output at 80%
• 1 Panel Charges 2- 6Volt Batteries or 1- 12Volt battery in 7-10 hours.
Tax Incentives!
The Federal Tax Code is offering through 2016 a 30% Tax Credit on Batteries, Panels, Wiring and any Installation Costs associated with your Solar Purchase. The Federal Tax Code is HR-1424. Check with your state for any other solar incentives and rebates they may have. Consult with your CPA or tax advisor.
Exterior for Sale
- Winegard roadtrip sd stationary satellite system rv 5th wheel travel trailer(US $300.00)
- Rv cargo door r.o. 26" tall x 16" wide x 1 1/4" thick ( used )(US $9.98)
- Rv cargo door r.o. 28" tall x 18" wide x 3/4" thick rough white(US $9.99)
- Rv cargo door r.o. 26" tall x 18" wide x 3/4" thick design(US $9.99)
- Rv cargo door r.o. 26" tall x 18" wide x 3/4" thick rough white/black trim (US $9.99)
- Rv cargo door r.o. 30" tall x 14" wide x 3/4" thick tan (US $9.99)
Jaguar to handbuild new £1m E-type Lightweights (2014) first pictures
Wed, 14 May 2014By Phil McNamara First Official Pictures 14 May 2014 09:16 Jaguar’s E-type is coming back from the dead, in ultra-rare ‘Lightweight’ form. A special team of craftsmen will handbuild six cars, all picture-perfect reproductions of the legendary Lightweight E-types from 1963-64. The 'new' cars are expected to sell for around £1 million each; established Jaguar collectors with a thirst for racing and a desire for a wondrous slice of motoring memorabilia get your name down now.
New BMW M3 and M4 engine secrets laid bare
Thu, 26 Sep 2013BMW's M division has lifted the veil of secrecy on the inline six-cylinder engine bound for its upcoming M3 sedan and new-to-the-range M4 coupe and convertible, revealing a potent twin-turbocharged 3.0-liter direct injection gasoline unit that produces an official 424 hp at 7,500 rpm and what officials describe as "significantly more than 369 lb-ft" of torque. The newly developed engine, known under the internal codename S55 B30, shares its 84.0 mm bore and 89.6 mm stroke with BMW's standard turbocharged 3.0-liter in-line six-cylinder direct-injection gasoline mill, the M55 used across the German car maker's lineup, endowing the aluminum block unit with an overall swept volume of 2,979 cc. This represents a sizeable 990 cc reduction on the engine BMW's M division's new unit replaces, the S65.
Mitsubishi to build new family of vehicles in U.S.
Mon, 17 Jan 2011Mitsubishi will assemble a new family of vehicles at its Illinois plant within two years, a source familiar with the company's plans said. The vehicles will be based on the platform underpinning the Outlander and Outlander Sport crossovers and Lancer sedan, the source said. Those models are assembled in Japan.