Find or Sell any Parts for Your Vehicle in USA
Car & Truck Parts > Gauges > Volt Meters

Hho Ccpwm 30khz 70a Pwm Pulse Width Modulator Super Pro Control Hho on 2040-parts.com

AU $205.00
Location:

Malanda, QLD, Australia

Malanda, QLD, Australia
HHO CCPWM 30KHZ 70A PWM PULSE WIDTH MODULATOR SUPER PRO CONTROL HHO, AU $205.00, image 1 HHO CCPWM 30KHZ 70A PWM PULSE WIDTH MODULATOR SUPER PRO CONTROL HHO, AU $205.00, image 2
Condition:New Compatible Makes:Jaguar HHO GAS DRYER:GAS DRYER HHO GENERATOR:FUEL SAVER 12v and 24 VOLT:24 VOLT MOTOR CONTROL:12 VOLT Brand:NQHYBRIDS CE & FCC APPROVED PWM:PULSE WIDTH MODULATOR Manufacturer Part Number:NQCCPWM70 HHO PWM:HHO CCPWM

You are buying a brand new  70AMP  30KHZ   SUPER PRO  CCPWM  (CONTANT CURRENT Pulse Width Modulator)

This item is new and in its box and is designed for HHO sytems and 12 volt motor control.                  R

This latest CCPWM is the top of its kind and is set and forget unit. with a massive pulse adjustment range from 0 to 3000khz    Your HHO Generator will run cooler and make more hydrogen which has greater ability to increase fuel mileage. Fully adjustable from the out side Turn from 12 to 24 volts easily , no internal adjustment , plus the ability to turn ther whole unit off. Comers wit ecxtra switching weires for level indicatore, earth leakage and many other choices


Intelligent Current Controller!

(1) Changing Amps directly, not changing the duty cycle.

(2) Fix a value of output current and SuperPro will make your

cell working at this value or lower. Don't need to worry

about over drawing power from battery and alternator. It

protects your batter y and alternator in an other worlds.

(3) Super Pro' can work in both 12V and 24V by a small easy

switch inside the case. Don't need to change the cooling fans.

(4) Max Output 75AMPs, 30KHz

(5) Different Frequency ranges selecting for more different

purpose operations.

(6) Auto Save. The Frequency and Duty Cycle can be auto saved. When the data

achieves your need, stop tuning for 1 second. The data can be auto

saved.

(7) Memory After the Duty Cycle and the Frequency was saved, Super Pro runs at this recorded data next time when it is powered on.

(8) Safety wires for different type of sensor switches.

(9) Dual in Dual out wires, easy connection.

(10) Size 19.5x16.1x7.5cm

(11) Net Weight: 0.95kg


 


 

The PWM HHO Generator Controller FCC & CE APPROVED

 For more information  Ph 40972713 or nqhybrids@activ8.net.au


This PMW may be used on any 12 volt or 24 volt system                                                              

ALSO AVAILABLE AT NQ HYBRIDS

HHO CELLS,   BUBBLERS,   GAUGES,   ¼ HOSE BARBS.  ONE WAY CHECK VALVES,  PWM’s  ELECTROLYTE LEVEL INDICATORS.    EFIE’S.  VAPORIZERS

Complete 11 Plate HHO Version 7 dry Cell kits to suite up to 2.5 litre petrol or diesel engines

  or

Complete 21 Plate HHO Version 8 dry Cell kits

to suite up to 5 litre petrol or diesel engines.

SETS INCLUDE

To be Assembled 11 Plate Dry Cell

1800mm #10 Black wire

1800mm #10 Red wire

1800mm reinforced 1/4" tubing

6 Cable ties

8 Self Tapping Mount Screws

8 Hose Clamps

12 Electrical Connectors

1 30 AMP Gauge

 Purpose built HHO 1 litre Bubbler tank

4 Hose Barbs

1 Vaporizer/Scrubber/Spark arrestor

1  1/4 Check valve

waterproof 30amp fuse holder 

BONUS 30 AMP PWM

30/40 AMP RELAY

All electrical tabs and fittings needed.

 

 

EFIE   (Electronic Fuel Injection Enhancer)

 Fuel Injection

Fuel injected vehicles use a computer and sensing devices to sense and maintain the correct air/fuel ratio. One of the key sensing devices is the oxygen sensor. Fuel injected vehicles have one or more oxygen sensors installed in the exhaust stream. The computer extrapolates what the air/fuel ratio is based on the amount of oxygen in the exhaust, as reported by the oxygen sensor.
When Hydrogen on demand device is installed, the petroleum based fuel is burned more completely. One of the results of this is that there is more oxygen (and less unburned hydrocarbons) in the exhaust stream. This is a good thing, and is in fact, what we are trying to achieve. However, the computer will perceive this condition as a "too lean" air/fuel mix. In other words, what is now a desirable condition in the exhaust will be interpreted as "not enough gas", and the computer will direct the fuel injectors to increase the amount of gas being pumped into the engine.The result is that the oxygen sensor and computer prevent efficient combustion from occurring

The Solution
The oxygen sensor "tells" the computer what the oxygen content is by providing a voltage on it's signal wire between 0 and 1 volt. 450 millivolts (.45 volts) means that the fuel/air mixture is correct. Higher values means the mix is rich (has too much gas), and lower voltages means the mix is lean. By adding voltage to the sensor's output, we can compensate for the additional oxygen in the exhaust.
The Electronic Fuel Injection Enhancer (EFIE) does exactly this. It adds a floating voltage to the top of whatever the oxygen sensor is putting out. It has an adjustment that allows you to control, to within a few millivolts, the amount of this added voltage. This allows the computer to be unaware of the additional oxygen content of the exhaust, and the electrolyzer can now achieve it's full potential in fuel savings.
Most cars have oxygen sensors both before and after the catalytic converter. The ones downstream from the converter do not need to be treated. Their data is used to determine when the converter has gone bad, but are not used in the air/fuel calculations. EFIEs are only needed for all upstream oxygen sensors

Wideband Quad EFIE

This is the EFIE for V6 and V8 engines that are equipped with wide band oxygen sensors. Note: Vehicles that use wide band sensors only use them upstream of the catalytic converter. The downstream sensors will still be narrow band. Therefore this product has 2 wide band EFIEs and 2 narrow band EFIEs

                                             

Wideband Dual EFIE 

This is the EFIE for 4 cylinder engines that are equipped with wide band oxygen sensors, or any vehicle with one wide band and one narrow band sensor. Note: Vehicles that use wide band sensors, only use them upstream of the catalytic converter. The sensors will still be narrow band. Therefore this product has a wide band EFIE and a narrow band EFIE

               

 Relay

The HHO generator wiring has one important necessary feature: its ability to automatically turn on and off the HHO gas generator.
Instead of using a toggle switch to operate the HHO system, a relay is installed. What is a relay?  A relay is an electrical switch that controls another circuit. It is also a device that contain an electrical winding motor inside which when powered up, will allow connection of 2 wires or circuits together. This is important in our Hydrogen on demand wiring which needs to be shut off when we stop the engine. If we are using a toggle switch to turn the HHO generator on, there is a chance that we can forget to shut the toggle switch off.  HHO Is EXPLOSIVE The relay is activated when you turn on the ignition and is turned off accordingly. You can fit a toggle switch in between to deactivate the HHO system as a method of override.  ALL NQ HYBRID SYTEMS COME WITH A 30 AMP RELAY

  

THE BUBBLER

The Bubbler: is a simple flashback device, used to prevent the burning gas from entering the HHO gas generating chamber and creating an explosion.The HHO coming from the cell moves the electrolyte around. The bubbler acts a reservoir to help with heat build                                                 

ALL NQ HYBRID SYTEMS COME WITH A BUBBLER

ELECTROLITE

Now the installation of your unit should be complete. You are now going to Mix the Catalyst (electrolyte) with Distilled Water. KOH is recommended.                               Potassium hydroxide is an inorganic  compound with the formula KOH. Its common name is caustic potash. Potassium Hydroxide is the best electrolyte for a Hydrogen Generator. We wont use any thing else for catalyst in our HHO Dry cells                                                                                       
The strength of your electrolyte mixture is what controls the amps drawn by your dry cell. To keep my unit running at 18 Amps or less and get a least 1 liter per minute of gas or more)
 Start with 100gms of KOH to 900 gms of  distilled water for start up , you may need to add more  to get higher amps but run your unit with a weak solution to condition it first.
** Use "Safety First" rules when mixing KOH or other caustic materials. Mix thoroughly in a separate container.
* Once this has been mixed add to the reservoir, you should be able to see the water flowing into the dry cell. Bring the level up to the 3/4 mark on the reservoir and make sure to put the cap back on.
*** Now you HHO Dry Cell System should be fully functioning and ready for a test drive. Before you take a test drive start the vehicle, you should now see the water in full circulation. Double check for air and water leaks at this time BY getting a spray bottle and a teaspoon of dish soap once mixed spray on all of your hose connectors, bubbler cap and reservoir cap, if there are bubbles you have a leak and this needs to be fixed.

Always read MSDS data sheets when using corrosive / caustic solutions

Disclaimer In no event will nqhybrids be liable for any loss or damage to any vehicle or person including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from the use of our products. NQ Hybrids recommends a competent person installs there units and the purchaser does does his or hers own research on the use of these exsperimental fuel cells.

 

Powered by eBay Turbo Lister

November auto sales jump 17 percent as market gains strength

Wed, 01 Dec 2010

U.S. car and truck sales jumped 17 percent last month, raising hopes the industry will end 2010 on a high note while creating momentum for the new year. Light vehicle sales rose to 873,407 units in November, for the market's 11th advance in the past 12 months.

BMW 335iS (2011) prices +video

Thu, 28 Jan 2010

The BMW 335iS Convertible - starts at $59K Normally we would have made the headline ‘BMW 355iS US prices’, but as BMW has decided that the new 335iS is going to be a North America car only we guess that anyone looking for a price will know it’s going to be a dollar price. As we reported last week, BMW are releasing the 335iS to bridge a gap they perceive exists between the 335i and the M3. Which seems more like the sort of think Audi would do rather than BMW, but perhaps they’ve learnt a trick or two from their four-ringed neighbours about filling every possible niche?

First BMW i8 Hybrids delivered to customers – complete with Laser Lights

Fri, 06 Jun 2014

The first BMW i8s delivered in Germany The new BMW i8 hybrid supercar was finally revealed in production guise at last year’s Frankfurt Motor Show, and by the time it went in to production the whole of the 2014 run of i8s was sold out. Apart from its innovative plug-in hybrid powertrain, the i8 offers many new technologies, one of which is a set of laser lights which deliver a much brighter main beam than LED and looked set to be the first time such lights have appeared on a production car. But Audi tried to upset BMW’s applecart by revealing the R8 LMX last month, which also came with laser lights, and looked set to arrive with customers before the i8.

2040Parts.com © 2012-2025. All Rights Reserved.

Designated trademarks and brands are the property of their respective owners.

Use of this Web site constitutes acceptance of the 2040Parts User Agreement and Privacy Policy.

0.04 s, 12315 u