Kinsler Bypass K-jet Assortment,.100"-.108",5 Fuel Pills For -6an Jet Can Valves on 2040-parts.com

You are bidding on a Brand New Kinsler K-Jet / Fuel Pill Assortment for Kinsler, Hilborn, and Waterman -6 AN Bypasses.

K-Jets are the industry-leader in fuel injection.

Includes 5 Jets:

• .100" Inside hole diameter - Kinsler #3715-100
• .102" Inside hole diameter - Kinsler #3715-102
• .104" Inside hole diameter - Kinsler #3715-104
• .106" Inside hole diameter - Kinsler #3715-106
• .108" Inside hole diameter - Kinsler #3715-108

Features:

• These are "drop-in" jets for 6 AN jet cans/bypass valves, including Hilborn, Kinsler, and Waterman 6 AN valves
• Kinsler K-Jets:
  • Kinsler prides themselves on the K-Jets being precise, accurate, and consistent
  • A perfect fuel injection system is of little use to the owner unless he has a good set of jets to use with it.  When using commercially made jets, it is not unusual when going .005" smaller in jet size (in an attempt to richen the unit) to actually find no fuel rate change, or perhaps go grossly rich, or even to go a bit leaner!  This can make it impossible to "tune in" the engine for best power and consistency
  • Each K-jet is precisely machined and stamped with the "KINSLER" name to identify it.  It has a reamed orifice controlled within .0002", a precise radius leading to the orifice, and a regulated finish
  • Every K-jet is tailored on the flow bench to within 1% of the flow rate of the master reference jet of its same size.  Therefore, even though the increments between the K-type jets are very small, if one jet is lost, an exact duplicate can be shipped immediately
  • Drop-in style jets give several advantages:
    • No damage to the jet on installation or removal like some screw-in commericial jets;  screwdriver nicks on the face of the inlet to any orifice can cause the flows to change
    • The jet rests on an o-ring for positive seal;  no possible leakage which could alter the flow, affecting the tuning of the engine
  • Typical increments versus application:
    • .002" for gasoline and small alcohol engines
    • .004" for typical alcohol V8 engines
    • .004" to .008" for blown applications
    • .006" to .010" for high speed and secondary restrictor jets
  • Important K-Jet notes:
    • When installing a K-type jet that is replacing a commercial jet, start with a K-Jet that is about .008" smaller; this is due to the efficient design of the K-jets
    • Always install the jet so that the number is facing up as the jet is dropped in (shown below), then the fuel will flow into the radiused side of the jet;  after the jan can has been assembled, the number will be facing toward the poppet
    • Make sure the jet can end has an o-ring receiving groove and that an o-ring is in place for the jet to rest on;  Note: the jet sealing o-ring should be replaced periodically to make sure that the compound has not "dried" out
    • Any marks on the radius of a K-jet were put there on purpose during the flow tailoring process....leave them there!
    • Never string the jets on a wire, as their entrance shapes will change as they move around on the wire!!!
  • Reasons for flow errors on commercial jets that the K-jet will eliminate:
    • Variations in the orifice size;  even the same drill doesn't make the same size orifice each time.  Reaming is the only way to insure exact orifice size
    • Entrance conditions;  these can make a considerable difference in flow, yet are often overlooked.  Even though both of the jets in the picture below have the same fuel pressure to them, and the same orifice size, the flow through the jet on the right will be about 20% greater than that of the jet on the left.  This is due to the generously rounded entrance, which makes it easier for the minute particles (molecules) of fuel to get into the orifice.  You can see Kinsler's in-depth Orifice Theory write-up here and here.
    • 
    • Most commercial jets have a square edge, with a simple chamfer.  A K-jet has a large radius that is precisely blended to the bore, giving better control of the entrance conditions and better protection of the orifice
    • All of the problems mentioned above are eliminated by using K-jets, since each jet is precisely machined, then hand-tailored to the flow of a master reference jet

In our Ebay store, we have available:

• Other assortments of K-jets
• Standard Hilborn jets
• Waterman's o-ring jets
• Kinsler Bypass Valves
• Waterman Bypass Valves
• Kinsler Jet Selector valve
• Kinsler Range Jet valve

K-Jet Installed in Jet Can:

In our Ebay store, we have many other Kinsler products, as well as thousands of other Sprint Car, Midget, and Mini-Sprint items.

We also have thousands of other High Performance Parts in our store.

Shipping:

There is no faster shipping on Ebay.  If you pay for the item by 5:00 Eastern, Monday-Friday, we will ship it the same day.  If it's after 5:00 EST, we will ship it the next business day.  If you pay for the item on the weekend, we will ship it out Monday.

Ebay now requires that sellers put a "handling time" on each item and "1 Business Day" is the shortest listed option.  WE DON'T HAVE A HANDLING TIME.  We ship same day in accordance with the paragraph above.  No delays here.  We want you to have the parts as bad as you do. 

Shipping cost will be $9.99 within the continental United States.  If you buy 2 or more of our auctions, shipping will certainly be combined to save you money.  We will be glad to ship internationally.  Just send me a message for an international shipping quote.

Accepted payment methods:

We accept Paypal. If buyer doesn’t have a Paypal account, he or she can pay with Visa, Mastercard, or Discover through seller’s merchant account.