Mopar 1946 1947 1948 Dodge D24 230 Cid Rebuilt Engine 46 47 48 on 2040-parts.com
Omaha, Nebraska, US
Mopar 1948 Dodge D24 230 CID Rebuilt Engine
You are looking at a rebuilt Dodge D24 230 CID .040 over engine.
This model was used in Dodge vehicles years 1946, 47 and 48.
However, the basic engine design was actually used by Dodge from 1942 - 1954 with minor modifications along the way.
This unit is ready to go for a driver vehicle or restoration project.
It was carefully stripped to the block and hot tanked to remove all traces of oil, dirt, and debris. The water diffuser, which slips in the block behind the water pump, was in perfect condition! As you may well know, these alone are becoming scarce to find and usually don’t come out in one piece.
Inspected block for cracks under UV light after initial cleaning, bored .040 over to accommodate a set of 6 new pistons, pins, and rings, then back in the hot tank for a final cleaning.
Engine was reassembled with new frost plugs, cam bearings, rods, main bearings and a polished crank.
All 6 intake valves were replaced with new, and the exhaust valves refaced.
All 12 valve seats were reground as well during the process.
A new timing chain was installed on the timing gears (which showed virtually no wear) and valves adjusted to specifications.
This engine was then completely reassembled with new gaskets and seals.
Upon reassembly the generator, starter and distributor and oil pump were also rebuilt, tested, and installed.
New ignition components installed and new asbestos gaskets for the electric choke seat on the intake manifold.
This unit comes with the original fluid drive assembly, and housings (lower housing not shown installed in pictures). Accessory oil filter with new filter, and clutch fork (also not shown)
When completed, the engine was started and tested on the engine stand and operated with oil pressure of 40 lbs. at an idle speed.
What you will need for this engine are the following: fuel pump, fan belt, and carburetor, which are readily available. ( I stock them )
This will make a nice powerful engine for someone without all the hassle of have one sent out for a rebuild.
The engine stand is not included.
Shipping Details: Local pickup only or it may be possible for me to deliver within 100 miles of Omaha, inquire before bidding please.
If you have any questions regarding this engine please contact Frank @ 402 943-9787
Thank you!
This model was used in Dodge vehicles years 1946, 47 and 48.
However, the basic engine design was actually used by Dodge from 1942 - 1954 with minor modifications along the way.
This unit is ready to go for a driver vehicle or restoration project.
It was carefully stripped to the block and hot tanked to remove all traces of oil, dirt, and debris. The water diffuser, which slips in the block behind the water pump, was in perfect condition! As you may well know, these alone are becoming scarce to find and usually don’t come out in one piece.
Inspected block for cracks under UV light after initial cleaning, bored .040 over to accommodate a set of 6 new pistons, pins, and rings, then back in the hot tank for a final cleaning.
Engine was reassembled with new frost plugs, cam bearings, rods, main bearings and a polished crank.
All 6 intake valves were replaced with new, and the exhaust valves refaced.
All 12 valve seats were reground as well during the process.
A new timing chain was installed on the timing gears (which showed virtually no wear) and valves adjusted to specifications.
This engine was then completely reassembled with new gaskets and seals.
Upon reassembly the generator, starter and distributor and oil pump were also rebuilt, tested, and installed.
New ignition components installed and new asbestos gaskets for the electric choke seat on the intake manifold.
This unit comes with the original fluid drive assembly, and housings (lower housing not shown installed in pictures). Accessory oil filter with new filter, and clutch fork (also not shown)
When completed, the engine was started and tested on the engine stand and operated with oil pressure of 40 lbs. at an idle speed.
What you will need for this engine are the following: fuel pump, fan belt, and carburetor, which are readily available. ( I stock them )
This will make a nice powerful engine for someone without all the hassle of have one sent out for a rebuild.
The engine stand is not included.
Shipping Details: Local pickup only or it may be possible for me to deliver within 100 miles of Omaha, inquire before bidding please.
If you have any questions regarding this engine please contact Frank @ 402 943-9787
Thank you!
Complete Engines for Sale
Ford 289 turn key mild performance balanced engine(US $4,995.00)
Cadillac flathead v8 tank engine?(US $2,500.00)
Chevy ii nova four cylinder 4 marine engine(US $200.00)
413 mopar engine with transmission belvedere,coronet(US $250.00)
1961 - 1966 ford f100 292 complete running engine and transmission motor 1956(US $250.00)
1967 ford fe 390gt engine block (7e) 390 gt heads (7e) intake (7c) pump (7e)(US $1,995.00)
Who's Where: Jason Castriota joins Stile Bertone
Thu, 27 Nov 2008Contrary to what was previously disclosed, Car Design News has now confirmed that Jason Castriota, who left his position at Pininfarina on the eve of the Paris Motor Show in September, is set to become Design Director at Stile Bertone. He will start his new position on December 1. Castriota had initially intended to set up his own design consultancy before being approached by Bertone.
Audi to bring more diesels to U.S. market
Tue, 08 Mar 2011Encouraged by healthy U.S. demand for diesel-powered versions of the A3 hatchback and Q7 crossover, Audi will add diesel powerplants to the A8 and A6 sedans and the Q5 crossover within the next 24 to 30 months, Audi of America Inc. president Johan de Nysschen said Tuesday.
Nissan may build more Leaf EVs to meet growing demand
Wed, 07 Aug 2013Nissan is making plans to begin building more electric Leafs as dealers clamor for more of the once slow-selling car. The automaker's North American factory chief -- who has been visiting with retailers in recent days -- cautions that production will move ahead in small and careful steps. But Nissan is already taking measures to increase its output of electric motors from its engine factory in Decherd, Tenn., says Bill Krueger, Nissan Americas vice chairman and senior vice president for manufacturing, purchasing production engineering and supply chain management.