Nine Inch Ford 100% New 3rd Member Nodular Iron And Trac Loc Fast Track Order on 2040-parts.com

 with your CHOICE

3:50     3:50    3:70    3:89    4:11    4:57 

We have well over 50 combinations of Ring and Pinions in stock based on your needs

We have standard race sets ( Nascar and road race ) Quiet Street Gears , Pro Gears for Drag Race

Gears from 3:00 to the Mid 7:00 in ratio. We even have special Bonneville gear sets based on SPECIAL

CARRIERS built on the 9 inch Ford Technology to get you in the mid 2:00 ratios 

SIMPLY EMAIL US FOR SPECIAL NEEDS QUOTE AND WE CAN POST A SPECIAL AUCTION 

 ( BRAND NEW PREMIUM GEAR SET )

 QUIET GEARS  for your STREET MACHINE 

And a 28 or 31 spline with BRAND NEW Trac Loc

STREET  POSITRACTION

and the best for last

SPECIAL BRAND NEW

NODULAR IRON 3rd MEMBER

with Billet Steel Caps 

Trac Loc 9" Ford case is stronger than the OEM unit.

3rd MEMBER ....NO CORE CHARGE (sold OUTRIGHT)

Limited time FREE SHIPPING to any

of the LOWER 48 STATES 

• THIS AUCTION IS FOR ONE (complete)
• NINE INCH FORD CENTER SECTION
• 
  
• 100% BRAND NEW 
• Third member will  ship in with no paint ( BRAND NEW NODULAR 3rd MEMBER )
• The original FORD RED COLOR is shown simply for this ad 
• as 99% of Ford users EXPECT to see the ORIGINAL FORD RED  
• ( the original Ford Red had lead in paint and is now ILLEGAL in all USA  )
• 
  
•  Note ... All pictures are FILE  PHOTOS with  CASE painted Red to show up on internet to show detail 
• Your NEW NODULAR IRON CASE will ship in NATURAL COLOR ...No Paint 
• 
  
• ( see note below that explains rear end filler  )
•  
•            Third Member only ...
• using your EXISTING REAR END housing
•  
• NOTE ... Most 9 inch Ford rear ends have FILLER / FLUID LEVEL check plugs on back side of rear end housing  ... SOME YEARS only have FILLER / FLUID level check plugs on side of 3rd member ... IF YOUR VEHICLE HAS ONLY THE 3rd MEMBER FILLER / FLUID level TELL US ... we have some 3rd members with FILLER / FLUID check plugs ..............If you end up with combination where you have NO FILLER / FLUID LEVEL we can get you the same WELD IN SPUD/PLUG that we use on our  Nascar Oval track housings ...This WELD IN SPUD / PLUG can also be used on the bottom of rtear end housing for a DRAIN PLUG which some Ford nine inch rear ends never had  !    

• THIS AUCTION IS FOR ONE 3rd MEMBER with Posi Traction Unit and
• a) Your choice of gears ( BRAND NEW GEAR SET ) See drop down gear selection box at           
•                       
• b) STREET  POSITRACTION  with 28 or 31  splines

  See drop down gear selection box at top of ad 

c) Standard 1310 yoke (see below chart)

•        Note ... Call our TECH LINE and we will post a SPECIAL EBAY AUCTION
•                  for a 1330 yoke or a 1350 yoke

• •            ((( Third Member only ...using your EXISTING axle housing )))
  • 
    
   Note ... All pictures are FILE  PHOTOS with  CASE painted Red to show up on internet ... THANKS TO CALIFORNIA and States that joined California the           Ford Red no longer meets SAFE PAINT standards ...
•   

INFORMATION TO HELP YOU ORDER :  

Do you have  a 28 or 31 spline axle ? Most 31 spline axles came in PERFORMANCE FORDS 351 Clevelands / FE  427s / Boss 429s  etc Most 28 spline were  STANDARD HORSEPOWER CARS WHEN IN DOUBT ...Simply pull an axle and COUNT THE SPLINES  !     28 Spline Axle   31 Spline Axle Note the concave oval area  in center of axle flange.  Early 28 Spline axles are tapered. Counter sunk holes in center  indicate a 31 spline axle.  31 Spline axles are uniform in diameter.

What YOKE do you have ?

Shown is a 3 1/ 4" Saddle (1310) You will be measuring the saddle width (where the u-joint cups fit into the yoke).  The measurement will be either 3 1/4" (1310) or 3 5/8" (1330) or (1350)  The 1310 yoke is the most common with the 1350 almost never found in production car driveshafts. 1310  Yoke  Width 3 1/4" Cup diameter of U-joints  1 1/16" 1320  Yoke Width 3 5/8" Cup diameter of U-joints can be either  1 1/16" and/or 1 1/8 inch" 1330  Yoke Width 3 5/8" Cup diameter of U-joints 1 3/16"

How to determine whether you have a  Standard or Daytona pinion support.

3 1/2 " Yoke - Daytona Support From 3 5/8  to 4 1/2 " Yoke - Standard Support The exposed portion of the companion yoke will measure either 3 1/2" or  3 5/8" or  4 1/2".  Note that the measurement is taken with the companion flange installed in the housing.

Free shipping in the lower 48 states via UPS Ground

Visit our ebay store

We are Davis Motorsports of Reno ... We are one of the oldest and largest warehouses in the USA

We have been selling Professional Nascar Teams

NATIONWIDE  since  1958  !

January 2008 we celebrated our 50th year

and 3 Generations of selling Professional Racers 

LIMITED TIME

Free UPS SHIPPING  to any UPS-able address in lower 48 states  !

Visit My Store

Email us ...we will post a SPECIAL AUCTION

for Canada as low as $ 99 freight (Western Canada)

Au / Nz / Uk and Europe as low as $ 250 freight

ALWAYS EMAIL US YOUR COMPLETE

ADDRESS with POSTAL CODE and

PHONE NUMBER so we can quote you

EXACT SHIPPING COSTS

in the auction we post for you.