Obdii Obd2 Diagnostic Vgate Icar Iv350 Elm327 Compatible Wifi Encrypted on 2040-parts.com

Vgate iCar iV350 WiFi OBD2 ELM327 scantool Encrypted

Features

1. Fully compatible with ELM327 V1.4b.
2. All ELM327 supported software are available to use.
3. Faster than ELM327 four times or higher. (ELM327 is RISC 8bit 44MHz MCU, iCar is ARM 16bit MCU)
4. Due to the android diagnostic software becomes heavier to run, suggest to use on smart phone with CPU 800Mhz or higher, 1GHz recommended.
5. Built in power switch.
6. Low standby power consumption sleep mode.
7. Lower power consumption than ELM327
8. LED indicator is in the front side toward user for easier check of linking status.
9.  Support J1939 protocol more than ELM327.
10. WiFi 802.11 b/g and encrypted for better security.

Product Description

OBDII decode chip: ARM 16bit MCU
Firmware: ELM327 Version 1.4b compatible
Transfer baud rate: 4800 / 9600 / 10400 / 38400 / 500K
Input interface: OBDII male 16pin
Output interface: Wifi 802.11 b/g
LED Indicator: Power(red) / OBD(green) / Link(blue) (PC or smart phone)
Operating Voltage: 12V, including over voltage /shortage protection
Nominal Idle current: 45mA
Net Weight: 31g
Gross Weight: 60g
Wire Length: 0 cm
SSID: BUYOBD
Password: See item label
IP: 192.168.0.10
HTTP local port: 35000
Encryption: WEP128
Power: supplied by car OBD socket
Usage:
    1. Plug the scantool into Car OBDII female socket which is  usually below the driving wheel.
    2. Insert car key and switch to Accessory ON position for static data reading,
    3. Scan the iCar from your Desktop/Notebook PC/PDA wifi  device.
    4. Find "BUYOBD" to link. Enter password which is on the item  label.
    5. You may switch car key to Start position to read more dynamic data readings.

Communication Protocol

OBDII 16-pin DLC definition: 

1. n/a
2. Bus + (SAE J1850 PWM, VPW)
3. n/a
4. Battery -
5. Signal -
6. CAN High (ISO 15765-4)
7. K Line (ISO 9141-2, SAE J2234)
8. n/a
9. n/a
10. Bus - (SAE J1850 PWM, VPW)
11. n/a
12. n/a
13. n/a
14. CAN Low (ISO 15765-4)
15. L line (ISO 9141-2, ISO 14230-4)
16. Battery +

Only pins 2, 4, 5, 6, 7, 10, 14, 15, 16 defined by above standards read data.
Other customized pins are not supported.
Please confirm OBDII label located under front engine hood. 

Support OBDII/EOBD2 protocols:
    ISO 15765-4 (CAN-B 125Kbps, started since 2003 in USA)
    ISO 15765-4 (CAN-C 500Kbs, 11bit ID, 29bit ID, started since 2003 in USA)
    ISO 14230-4 (KWP2000) 
    ISO 9141-2 (5 baud init. 10.4 kbaud, replaced by 14230-4 gradually, stopped in USA in 2008)
    SAE J1850 VPW (10.4 kbaud, replaced by 14230-4 gradually, stopped in USA in 2008)
    SAE J1850 PWM (41.6 kbaud, replaced by 14230-4 gradually, stopped in USA in 2008)
    SAE J1939 the Data link connector standard

Shipment:

• to U.S.A, Australia and U.K, we use Epacket. it takes 1-2weeks.
•  to other countries, we use airmail. it takes 2-4weeks or longer register mail with tracking number.

Custom clearance:

 we will not be responsible for your custom clearance and any tax cost!

Return Policy:

• if you are not satisfied with the item for any reason, you can return it back by airmail and get your full refund.
• Return ship will be paid by buyer.

Feedback:

• We know how important your satisfaction with our products and service is!
• If you are not satisfied with our products, please contact us before you leave neotral and negative feedback. we think communication is very important for us to solve any problem.
• Positive is always welcome. this courage is very helpful.
• Thanks in advance!