Find or Sell any Parts for Your Vehicle in USA
Car & Truck Parts > Turbos, Nitrous, Superchargers > Turbo Chargers & Parts

T04e 13pc T3 Twin Turbo Kit+manifold+intercooler Kit 87-93 Ford Mustang 5.0l V8 on 2040-parts.com

Location:

Rowland Heights, California, United States

Rowland Heights, California, United States
T04E 13PC T3 TWIN TURBO KIT+MANIFOLD+INTERCOOLER KIT 87-93 FORD MUSTANG 5.0L V8, image 1
Condition:New Brand:Speed Daddy Part Brand:speed_daddy Manufacturer Part Number:TBKSDDT04ETX2+TMFM87S13P Sedan Hatchback Instruction Included:No Interchange Part Number:V8 Convertible UPC:DOES NOT APPLY

Wheel Hub Quick Release, Racing Seat Combos items in Speed Daddy Com store on eBay!
T04E 13PC T3 TWIN TURBO KIT+MANIFOLD+INTERCOOLER KIT 87-93 FORD MUSTANG 5.0L V8
Top Seller, Product & Service! Fast & Easy Shipping!
858.88

STORE CATEGORY
NEWSLETTER!
Add my Store to your Favorites and receive my email newsletters about new items and special promotions!

General Interest
WE ACCEPT
T04E 13PC T3 TWIN TURBO KIT+MANIFOLD+INTERCOOLER KIT 87-93 FORD MUSTANG 5.0L V8
Description


    High Compression/ Boosting T04E Turbocharger with Internal Wastegate

    The objective of a turbocharger is to improve the engine's volumetric efficiency by solving one of its cardinal limitations. A naturally aspirated automobile engine uses only the downward stroke of a piston to create an area of low pressure in order to draw air into the cylinder through the intake valves. The pressure in the atmosphere is no more than 1 atm (approximately 14.7 psi), so there ultimately will be a limit to the pressure difference across the intake valves and thus the amount of airflow entering the combustion chamber. Since the turbocharger increases the pressure at the point where air is entering the cylinder, a greater mass of air (oxygen) will be forced in as the inlet manifold pressure increases. The additional air flow makes it possible to maintain the combustion chamber pressure and fuel/air load even at high engine revolution speeds, increasing the power and torque output of the engine.


    Specifics and Benefits:

  • Capable of Boosting Horse Power up to 300+ BHP
  • High Quality Material, Cast Housing with Durable Steel
  • Internal Wastegate Insertion; No Need for Extra Add-On

    Exhaust (Turbo Manifold) Flange:Standard T3/ T4 4-Bolt
    Exhaust (Downpipe) Flange:Standard 2.50" Inner Diameter V-Band
    Intake Inlet/ Outlet:3.00"/ 2.00"

    Compressor:
    Trim:57
    A/R:.53
    Inducer:50.55
    Exducer:76.00

    Turbine:
    Trim:58
    A/R:.63
    Inducer:65.20
    Exducer:56.06

    High Performance Top-Mount Tubular Exhaust Turbo Manifold

    The heart of any Turbo system is the Manifold and the Turbocharger. These form the basis where the rest of the turbo system is built around. Turbo manifolds have only one, but the most critical purpose in turbo systems, and that purpose is to expel exhaust gas into the turbine of a turbocharger as efficiently as possible.

    There is no match for power and performance for tubular stainless steel manifolds. Tubular manifolds are made up of runners coming from each cylinder, meeting up at a collector. Tubular manifolds yield a higher efficiency rate, as each runner is generally the same circumference. This allows for a much smoother flow of exhaust gas to the turbo.

    Tubular stainless steel manifolds are chosen over cast manifolds for big power applications. Tubular stainless manifolds feature better and more consistent flow of exhaust gases. Most of the tubular Stainless manifolds also feature the placement of the wastegate flange towards the middle of the collector to allow accurate readings and precise control.


    Specifics and Benefits:

  • High Performance Tubular Turbo Racing Design
  • Made of High Quality T-304 Polished Stainless Steel Alloy Material for Strength and Durability
  • Tubular Design to Ensure Equivalent Exhaust Flow Rate from each Cylinder
  • Computerized Mandrel-Bended to Maximize Air Flow Smoothness
  • TIG Welded CNC Machined Flange for Resistance against Cracking and Wearing
  • Increase Engine Exhaust Output and Efficiency
  • Standard T3 (T03) Configuration Outlet



    • Lightweight Aluminum Bolt-On Intercooler

    When the charged air enters the end tank, it travels through the tubes of an Intercooler, in which the heat is transferred via fins, where cooler ambient air passes over the tubes. This mechanism further removes heat from air before exiting the opposite end tank and routing to the engine.

    Bar and Plate Intercooler functions identically to the Tube and Fin Core, with the exception that, charged air travels through its rectangular shaped passages, which have more surface area; thus, improves cooling effect and power of the charged air. The advantage of this type of intercoolers is that, since the bar and plate core affords up to 35% larger surface area for cooling, a physically smaller intercooler can be used and still retains the cooling efficiency of a larger tube and fin design. This is important for a builder who has a vehicle with a compact opening in the front of it or when there are immovable obstructions present.


    Specifics and Benefits:

  • High Performance Bar and Plate Turbo Racing Design
  • Made of High Quality T-6061 Aluminum Durable Material
  • Helps Reducing Engine Inlet Temperature
  • Allow More Horsepower at the Same Boost Level and Even More Power at the Higher Boost Level
  • Intercooler Size: 29.75" (L) X 6.25" (H) X 5.25" (W)
  • Core Size: 23.50" (L) X 6.25" (H) X 3.50" (W)
  • Inlet/ Outlet: 1.75"/ 2.625”
  • Direct Bolt-On Front-Mount Installation; Easy to Install



    • Bolt-On Aluminum Intercooler Piping

    Specifics and Benefits:

  • Made of High Quality T-6061 Lightweight Aluminum Piping
  • Powder-Coated Surface Finish
  • Inlet/ Outlet Outer Diameter: 2.50"/ 2.00"
  • 2.00" Piping Diameter
  • Perfect for Turbo DIY Project
  • Increase 65% Air Flow comparing with other Standard Piping
  • Extra Reducer Included



    • Adjustable Billet Aluminum Blow Off Valve BOV

    The Blow-Off valve (BOV) is a pressure relief device on the intake tract to prevent the turbo’s compressor from going into surge. When the throttle is closed rapidly, the airflow is quickly reduced, causing flow instability and pressure fluctuations. Surge can eventually lead to thrust bearing failure due to the high loads associated with it. Blow-Off valves use a combination of manifold pressure signal and spring force to detect when the throttle is closed. When the throttle is closed rapidly, the BOV vents boost in the intake tract to atmosphere to relieve the pressure, helping to eliminate surge.

    Specifics and Benefits:

  • Billet Aluminum Body with Anodized Finish
  • Draw In Surrounding Air and Release a Unique Discharge Sound
  • High-Quality Diaphragm and Short Stroke Significantly Increase Response
  • Dual Spring System Promoted Response and Allows for High Boost Pressures
  • Holds Up to 30 PSI Boost Pressure
  • 2 Bolt Mounting Design


    Aluminum 2.5” Flange Pipe

    Specifics and Benefits:

  • Fits SSQV Dump Pipe Flange
  • Construction Prevents Warping due To High Heat
  • Made of High Quality T-6061 Aluminum, Lightweight Design
  • 2.50" Pipe Size



    • Stainless Steel Braided Oil Feed Line

    Oil feed lines and returns lines are an essential part of any turbo system. Oil feed lines bring oil to the turbocharger, at the same time the oil cools and lubricates the moving parts. The Oil Drain Lines take the oil that has passed through the turbo and guides it back into the engine’s oil pan. Without these two components, the turbocharger’s internals would overheat or seize causing major complications.


    Specifics and Benefits:

  • Made of High Quality Stainless Steel Hose
  • 10AN Fittings Anodized Ends
  • Inner Diameter: 0.25"
  • Length: 36.00"
  • 1/8 NPT Fittings Natural Polish Finish
  • CNC Machined Turbo Adapter Plate
  • Brass Fitting, Block Fitting, and Port Cover Included


    T3/ T4 5-Bolt Mild Stainless Steel Downpipe Flange

    Specifics and Benefits:

  • Made of High Quality T-304 Mild Steel Durable Material
  • Construction Prevents Warping Due To High Heat
  • 5-Bolt Design Shape
  • 0.50” Thickness Flange
  • Fits T3/ T4 2.5" Diameter 5-Bolt Turbo/ Turbocharger Flange
  • Included for DIY Welding Need



    • 100% Brand New
    Professional Installation is Highly Recommended (No Instruction Included)



    Package Includes:

  • 2 X T04E Turbocharger
  • 1 X Stainless Steel Turbo Manifold
  • 1 X Lightweight Aluminum Intercooler
  • 1 X Set of Bolt-On Aluminum Piping
  • 2 X Type-SSQV Blow Off Valve Kit
  • 2 X Flange Pipe
  • 2 X Braided Oil Feed Line
  • 2 X T3/ T4 5-Bolt Flange
  • Hardware as Shown in the Picture Above

    4-Piece Piping Set Includes:

  • 4 X Aluminum Pipings
  • 3 X Silicone Hoses
  • 4 X Silicone Reducers
  • 14 X Bolt-Tight Clamps


    Compatible with:

  • 87-94 Ford Mustang V8
    (Fits Models Above with 5.0L V8 OHV Engines ONLY)

  • Please Check Compatibilities for Exact Years and Models


    Modification might be Required for Some Vehicles


Related Products
DOMESTIC LOWER 48 US STATES:



SALES TAX:		 FREE



CA ONLY
VERY IMPORTANT:
Double check shipping address. We are not responsible for incorrect or undeliverable addresses.

Please use Shipping & Payments tab on top of page for shipping details for your location.

Shipping to PR, HI, AK and PO Box addresses will be charged the same as shipping to Canada. GU, VI, SAIPAN will be charged the same as international shipping rate.

For Canada shipping please select the lowest price. We do not offer expedited shipping.

US Territories such as GU, VI, SAIPAN will be charged the same as international shipping rate. Transaction will be held until a full shipping amount received.

Some of the packages cannot be delivered to a PO Box. Customer is responsible to ensure PO Box address given is deliverable by the shipping company. Package will be held until a valid physical address is provided.

Customer assumes shipping charges incurred in shipping to undeliverable address.

International buyers are responsible for all customs duties, taxes, and other applicable fees incurred by the country's customs/border regulations. Please contact customs for more information.

We ship 98% of all orders the same or next business day after payment received/cleared. Please understand that once orders are shipped, we cannot control the transit times thereafter. Most orders will ship via USPS First Class/Priority Mail or FedEx/UPS or the best suitable carrier for the specific size of the product.

We are not responsible for any changes to address after item has been shipped.

Porsche Panamera hits the heights in Shanghai

Wed, 22 Apr 2009

A Porsche Panamera on its way to the 94th floor of the World Financial Centre in Shanghai [ad#ad-1] The stories of car makers doing daft things with cars to garner a bit of publicity have been rarer of late. Which, considering the sombre mood of car makers and the car buying public in recent months, is no real surprise. Even Motor Shows have been relatively sombre affairs (the Detroit Motor Show was particularly muted in 2009), but China is still booming, and the Shanghai Motor Show has been pretty much an old fashioned, glitzy affair.

Aston Martin DB9 Facelift revealed

Mon, 28 Jun 2010

The subtly facelifted Aston Martin DB9 Remarkably, the Aston Martin DB9 has been with us since 2003. Yet it still conspires to look as fresh and appealing – and let’s face it, just downright beautiful – as it did when it launched. But standing still for too long is a dangerous game in business, so Aston Martin has decided the time has come to give the Aston Martin DB9 a facelift - as we reported in May.

Design Contest: Michelin Challenge Design announces 2007 theme and call for entries

Wed, 01 Feb 2006

At the 2006 North American International Auto Show, Michelin Challenge Design announced its theme for the 2007 Challenge. Michelin Challenge Design will ask entrants to explore the future of transportation design using safety as the focus and inspiration. "Road Safety for Everyone" is the official theme in what has become one of the industy's fastest-growing design forums.

2040Parts.com © 2012-2024. All Rights Reserved.

Designated trademarks and brands are the property of their respective owners.

Use of this Web site constitutes acceptance of the 2040Parts User Agreement and Privacy Policy.

0.051 s, 11823 u