Purchase Twist Boat Wrap - Customized for your boat - Choose Your Color in Naples, Florida, United States, for US $595.00

Condition:New Decal Type:Wrap Country/Region of Manufacture:United States

"Twist" Boat Wrap

Phone (239) 431-7356 Monday-Friday 8am to 5pm (e.s.t)

Sold in directional pairs, one left and one right side.
This wrap purchase is for a boat wrap to fit on a boat that is between 18 feet to 20 feet in length
From the rubrail down to the waterline.**
Longer boats may cost a little more. Smaller boat sizes are fine as well.

We will customize the wrap AFTER purchase to fit the actual year, make and model of your specific boat
to show the most available image area to achieve the best visual display.

Our boat wraps can be fitted to accommodate most boat models.

Once ordered and paid for, you will NEED to provide the
year, make, model, length of your boat and a side shot picture
as well as very accurate dimensions.
SEE EXAMPLE OF HOW TO MEASURE BELOW
Please email us with details.
Once you have approved the layout, we will manufacture it and ship within 36-48 hours. All products made on site.

Wrap will have excess in the front and rear as well as the top and bottom to allow for appropriate amount of trim.
Set up to be trimmed at the nose and a few inches around the back toward the motor.

Your graphics color may vary slightly from what you see depending

on you monitor Setting.

(boat not included, ha!)
Material is 3M IJ180 cv3 cast boat wrap vinyl film with 3M 8518 cast overlaminate for maximum UV protection.
Shipping to the lower 48 U.S. only. No shipping to Hawaii and Alaska.

Boat wrap by Wrap Graphics

Please try to follow these instructions to ensure success.

1. Specify the color or design you prefer, such as “Green” or "Diver & Octopus".

2. Submit an image of the boat. Make it a nice side shot like this example.
Submit images and artwork to:

3. Take some dimensions of the boat hull. Be sure to include the length along the rubrail,
the max depth from the rubrail down to the waterline edge where the wrap will end,
then along the hull every 2 feet or so as shown in the diagram.
Take Boat dimensions like this
4. Your wrap print will ALWAYS have more length and width than the actual dimensions
you send for “wiggle room” and proper trimming.

5. Be sure to include the year, make and model of your boat.

6. We submit a final mockup layout for your written approval showing the wrap you
chose superimposed on the image of your boat hull.

Mockup for proofing
7. Once we receive your approval the finished boat wrap is produced
and shipped within 36 to 48 hours.
YOUR WRAP WILL COME IN A RECTANGLE SHAPE AS SHOWN IN THE ABOVE
EXAMPLE. THIS ALLOWS FOR PLENTY OF TRIM AREA.

** 3b. If you want your boat wrap to go up over the rubrail into the gunwales, or if you want the bow or stern wrapped as well, you need to provide those dimensions as well. This will add to the cost. You can use the below diagram as a reference to ensure your wrap fits and presents itself the best.

We have many variations of our graphics and also provide custom colors upon request.
If you have any questions, Please don't hesitate to call.

Audi unveils new A3 interior at 2012 CES

Wed, 11 Jan 2012

Audi has revealed the interior of the next Audi A3 at the 2012 Consumer Electronics Show in Las Vegas... And what should I know about the insides of the new Audi A3? The interior of the A3 was unveiled at the Consumer Electronic Shows (CES) in Las Vegas, where there was lot of technical talk about plug-in modules and dual-core processors, but what you need to know is that the new A3 ushers in Audi’s next-gen modular infotainment platform.

McLaren F1 Video: Flemke’s Mac’s been fixed

Fri, 14 Oct 2011

Flemke's McLaren F1 on video Perhaps the best-know McLaren F1 in the UK – well, perhaps the best known apart from Rowan Atkinson’s recently bent F1 – is the F1 owned by regular online commenter ‘Flemke’. Flemke is, as you would expect, worth a few bob and lives in the UK. But unlike the vast majority of McLaren F1 owners he loves to share the joy of his Mac with online enthusiasts.

Porsche Boxster E (2011): prototype Boxster EV

Thu, 24 Feb 2011

Porsche recently rolled out the first of three Boxster E electric vehicles, to take part in the 'Electromobility Region Stuttgart' local government initiative in Germany. The Boxster E is powered by two electric motors, capable of a peak power output of 180kW. Energy is stored in a 29kWh battery pack. Not with the Boxster E. Three electric Boxsters are being built as part of a programme sponsored by the Baden-Wurttemberg state government (Porsche's home state in Germany) and WRS, the Stuttgart Region Economic Development Corporation. Porsche's hometown of Stuttgart is one of eight model regions participating in a federal pilot programme sponsored by the Minitsry of Transport, Building and Urban Affairs to develop EVs and their supporting infrastructure. The three Boxster E prototypes will take part in the programme, acting as mobile laboratories for testing EV usage and planning for EVs in urban infrastructure. CAR's view? We reckon this electric Boxster E is much cooler than your usual EV council van.

Twist Boat Wrap - Customized For Your Boat - Choose Your Color on 2040-parts.com

Decals for Sale

Audi unveils new A3 interior at 2012 CES

McLaren F1 Video: Flemke’s Mac’s been fixed

Porsche Boxster E (2011): prototype Boxster EV